海水暴露检测标准,检测中心-北检（北京）检测技术研究院

海水暴露检测标准相关信息

GB/T 7790-2008 色漆和清漆.暴露在海水中的涂层耐阴极剥离性能的测定
简介：本标准规定了暴露在海水中的涂层耐阴极剥离性能测定的试验方法，包括：方法原理、试验溶液、试验装置、试样及其制备、试验步骤、涂层的检查及试验结果评价、试验报告等。本标准适用于船舶及海洋工程结构物等暴露在海水中的金属基材上的涂层。本标准不适用于评估陆地结构物上的涂层。本标准规定的试验方法包括以下两种：方法A：外加电流法；方法B：牺牲阳极法。
信息：ICS：47.020.05 CCS：U05 发布：2008-07-30 实施：2009-02-01

DIN CEN/TS 15119-2-2008 木头和木基制品的耐久性.防腐剂处理的木头对环境的排放物的测定.第2部分:暴露在使用级别为4或45级的木制品(与地面、淡水或海水接触).实验室法
简介：
信息：ICS：13.020.30;71.100.50 CCS：B71 发布：2008-09 实施：

GB/T 5776-2005 金属和合金的腐蚀金属和合金在表层海水中暴露和评定的导则
简介： 本标准规定了金属和合金在表层海水中暴露所遵循的条件和方法，以便对不同地点的暴露做出意义的比较。本标准适用的暴露范围从水平面以上潮湿的重要区带(飞溅区和潮汐区)到水平面以下与表面海水组成相近的深度。本标准规定了海水对金属和合金腐蚀的评定方法。由于海水的可变性和复杂性，为减小可变因素的影响，暴露时间应在一年以上。
信息：ICS：77.060 CCS：H25 发布：2005-05-13 实施：2005-10-01

PD CEN/TS 15119-2-2008 木头和木基制品的耐久性.防腐剂处理的木头对环境的排放物的测定.第2部分:暴露在使用级别为4或45级的木制品(与地面,淡水或海水接触).实验室法
简介：
信息：ICS： CCS：发布：2008-05-01 实施：

GB/T 5776-1986 金属材料在表面海水中常规暴露腐蚀试验方法
简介： 本标准适用于金属材料（包括黑色、有色金属）在表面海水（海水深度在10m之内）中全浸、潮差及飞溅条件下的腐蚀试验。为海水腐蚀试验应遵循的一般程序，以统一试验条件和评价指标。
信息：ICS：77.060 CCS：H25 发布：1986-01-14 实施：1986-11-01

ASTM G52-00(2006) 表面海水中金属和合金的暴露和评估标准实践
简介：
信息：ICS：77.060 CCS：发布：2006-05-01 实施：

KS M ISO 15711-2021 色漆和清漆.暴露在海水中的涂层耐阴极剥离性的测定
简介：
信息：ICS：87.040 CCS：发布：2021-12-21 实施：

DIN EN ISO 15711-2005 色漆和清漆.暴露于海水中的覆层耐阴极解粘合作用的测定
简介：
信息：ICS：87.040 CCS：G50 发布：2005-03 实施：

ISO 23977-1:2020 塑料.暴露于海水中的塑料材料需氧生物降解的测定.第1部分:析出二氧化碳分析法
简介：
信息：ICS：83.080.01 CCS：发布：2020-11-10 实施：

ISO 15711:2003 色漆和清漆——暴露于海水中的涂层耐阴极剥离性的测定
简介：
信息：ICS：87.040 CCS：发布：2003-05-26 实施：

ISO 23977-2:2020 塑料.暴露于海水中的塑料材料需氧生物降解的测定.第2部分:用密闭呼吸计测量需氧量的方法
简介：
信息：ICS：83.080.01 CCS：发布：2020-11-10 实施：

ASTM G52-00 表面海水中金属和合金的暴露和评估标准实践
简介：
信息：ICS：77.060 CCS：发布：2000-05-10 实施：

ASTM G52-20 表面海水中金属和合金的暴露和评估标准实践
简介：
信息：ICS：77.060 CCS：发布：2020-11-01 实施：

ASTM G52-2000 金属及合金在海水表面暴露与评定的标准实施规范
简介：1.1 This practice covers conditions for exposure of metals and alloys to surface seawater, and sets forth the general procedures that should be followed in conducting seawater exposures tests so that meaningful comparisons may be made for different locations. 1.2 This practice lists suggested procedures for the evaluation of the effects of seawater on metals and alloys. Note 1-Terms relative to this subject matter can be found in Terminology G15. 1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.060 (Corrosion of metals) CCS：H25 发布：2000 实施：

ISO 23977-1-2020 塑料. 暴露于海水中的塑料的好氧生物降解的测定. 第1部分: 释放二氧化碳的分析方法
简介：
信息：ICS：83.080.01 CCS：发布：2020-11-00 实施：

ASTM G52-2000(2011) 表层海水中金属及合金的暴露和评价标准操作规程
简介：The procedures described herein are recommended for evaluating the corrosion or marine fouling behavior, or both, of materials exposed to quiescent or local tidal flow conditions, or both. 4.1.1 This practice is not intended to cover the influence of high seawater velocity or the behavior of materials in seawater which has been transported from its source. 4.1.2 Some aspects of this practice may be applicable to testing in tanks and troughs which are continuously provided with fresh surface seawater. Additionally, some aspects may also be applicable to deep ocean testing. Note 18212;Guide G 78 provides guidance for conducting crevice corrosion tests under controlled seawater test conditions. While the duration of testing may be dictated by the test objectives, exposures of more than six months or one year are commonly used to minimize the effects of environmental variables associated with seasonal changes or geographic location, or both. The procedures described are applicable for the exposure of simple test panels, welded test panels, or those configured to assess the effects of crevices, or both, such as those described in Guide G 78. In addition, they are useful for testing of actual components and fabricated assemblies. It is prudent to include control materials with known resistance to seawater corrosion or fouling, or both, as described in Test Method D 3623. Note 28212;Materials which have been included in ASTM Worldwide Seawater Corrosivity Studies include UNS K01501 (carbon steel), UNS C70600 (90/10 CuNi) and UNS A95086 (5086-H116 Al).2 4 Note 38212;In the case of evaluations of aluminum alloys, care should be exercised in the location of specimens near copper or high copper-containing alloys. In some instances, it is not sufficient to simply electrically isolate specimens to prevent bi-metallic (galvanic) corrosion; copper ions from nearby corroding copper or copper-base alloys can deposit on aluminum and accelerate its corrosion.1.1 This practice covers conditions for the exposure of metals, alloys, and other materials in natural surface seawater such as those typically found in bays, harbors, channels, and so forth, as contrasted with deep ocean testing. This practice covers full immersion, tidal zone and related splash, and spray zone exposures.1.2 This practice sets forth general procedures that should be followed in conducting seawater exposure tests so that meaningful comparisons may be made from one location to another.1.3 This practice identifies recommended procedures for evaluating the effects of natural surface seawater on the materials exposed.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.060 (Corrosion of metals) CCS：H25 发布：2000 实施：

KS D ISO 11306-2019 金属和合金的腐蚀 - 表面海水中金属和合金的暴露和评估指南
简介：
信息：ICS：77.060 CCS：发布：2019-10-31 实施：

ASTM G52-2000(2006) 金属及合金在海水表面暴露与评定的标准实施规范
简介：The procedures described herein are recommended for evaluating the corrosion or marine fouling behavior, or both, of materials exposed to quiescent or local tidal flow conditions, or both. 4.1.1 This practice is not intended to cover the influence of high seawater velocity or the behavior of materials in seawater which has been transported from its source. 4.1.2 Some aspects of this practice may be applicable to testing in tanks and troughs which are continuously provided with fresh surface seawater. Additionally, some aspects may also be applicable to deep ocean testing. Note 18212;Guide G 78 provides guidance for conducting crevice corrosion tests under controlled seawater test conditions. While the duration of testing may be dictated by the test objectives, exposures of more than six months or one year are commonly used to minimize the effects of environmental variables associated with seasonal changes or geographic location, or both. The procedures described are applicable for the exposure of simple test panels, welded test panels, or those configured to assess the effects of crevices, or both, such as those described in Guide G 78. In addition, they are useful for testing of actual components and fabricated assemblies. It is prudent to include control materials with known resistance to seawater corrosion or fouling, or both, as described in Test Method D 3623. Note 28212;Materials which have been included in ASTM Worldwide Seawater Corrosivity Studies include UNS K01501 (carbon steel), UNS C70600 (90/10 CuNi) and UNS A95086 (5086-H116 Al).2 4 Note 38212;In the case of evaluations of aluminum alloys, care should be exercised in the location of specimens near copper or high copper-containing alloys. In some instances, it is not sufficient to simply electrically isolate specimens to prevent bi-metallic (galvanic) corrosion; copper ions from nearby corroding copper or copper-base alloys can deposit on aluminum and accelerate its corrosion.1.1 This practice covers conditions for the exposure of metals, alloys, and other materials in natural surface seawater such as those typically found in bays, harbors, channels, and so forth, as contrasted with deep ocean testing. This practice covers full immersion, tidal zone and related splash, and spray zone exposures.1.2 This practice sets forth general procedures that should be followed in conducting seawater exposure tests so that meaningful comparisons may be made from one location to another.1.3 This practice identifies recommended procedures for evaluating the effects of natural surface seawater on the materials exposed.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.060 (Corrosion of metals) CCS：H25 发布：2000 实施：

ASTM G52-00(2016)e1 表面海水中金属和合金的暴露和评估标准实践
简介：
信息：ICS：77.060 CCS：发布：2016-11-01 实施：

NF A05-270-1998 金属和合金材料腐蚀.海水表层中金属和合金暴露和评估指南
简介：
信息：ICS：77.060 CCS：H25 发布：1998-05-01 实施：1998-05-20

ISO 16539-2013 金属和合金的腐蚀.暴露在合成海水盐沉积过程的加速循环腐蚀试验.恒定绝对湿度下的干燥条件和湿润条件
简介：
信息：ICS：77.060 CCS：H25 发布：2013-03 实施：

BS EN ISO 11306-1998 金属和合金腐蚀.金属和合金暴露于海水表面后的评估指南
简介：1 This International Standard gives guidance on the conditions and procedures to be followed when conducting exposures of metals and alloys to surface sea water such that meaningful comparisons may be made for different locations. This International Standard applies to exposure areas from above water level which are wet for a significant period (splash and tidal zones) down to a depth at which the composition of the sea water is similar to that at the surface.2 This practice gives guidance on procedures for the evaluation of the effects of sea water on metals and alloys.3 Because of the variability and complexity of sea water, exposures over a minimum period of one year are considered necessary to minimize the influence of these variable factors.
信息：ICS：77.060 CCS：H25 发布：1998-04-15 实施：1998-04-15

BS ISO 16539-2013 金属和合金腐蚀.暴露在合成海水盐分沉淀工艺中加速循环腐蚀试验.恒定绝对湿度下的干燥和湿润条件
简介：
信息：ICS：77.060 CCS：H25 发布：2013-02-28 实施：2013-02-28

DIN EN ISO 11306-1998 金属和合金的腐蚀.金属和合金暴露于海水表面及评定指南
简介：The document gives guidance on the conditions and procedures to be followed when conducting exposures of metals and alloys in surface water such that meaningful comparisons by be made for different locations.
信息：ICS：77.060 CCS：H20 发布：1998-04 实施：

ISO 11306:1998 金属和合金的腐蚀.在地表海水中暴露和评估金属和合金的指南
简介：
信息：ICS：77.060 CCS：发布：1998-02-12 实施：

ISO 16539:2013 金属和合金的腐蚀——暴露于合成海水盐沉积过程中的加速循环腐蚀试验&mdash恒定绝对湿度下的“干”和“湿”条件
简介：
信息：ICS：77.060 CCS：发布：2013-02-14 实施：

EN ISO 11306-1998 金属与合金的腐蚀.对海水表面的金属和合金的暴露和评估准则 ISO 11306-1998
简介：
信息：ICS：77.060 CCS：发布：1998-02-01 实施：

DIN CEN/TS 15119-2-2012 木材和木制品的耐久性. 经防腐处理的木材对环境的排放物的测定. 第2部分: 暴露于4级或5级使用的木制品(与地面, 淡水或海水接触). 实验室方法; 德文版本CEN/TS 15119-2-2012
简介：
信息：ICS：13.020.30;71.100.50 CCS：B69 发布：2012-12 实施：

ISO 11306-1998 金属与合金的腐蚀对海水表面的金属和合金的暴露和评估准则
简介：1 This International Standard gives guidance on the conditions and procedures to be followed when conducting exposures of metals and alloys to surface sea water such that meaningful comparisons may be made for different locations. This International Standard applies to exposure areas from above water level which are wet for a significant period (splash and tidal zones) down to a depth at which the composition of the sea water is similar to that at the surface.2 This practice gives guidance on procedures for the evaluation of the effects of sea water on metals and alloys.3 Because of the variability and complexity of sea water, exposures over a minimum period of one year are considered necessary to minimize the influence of these variable factors.
信息：ICS：77.060 CCS：H25 发布：1998-02 实施：

PD CEN/TS 15119-2-2012 耐用的木材和木制品.排放测定木材防腐剂的环境.第2部分:木制商品暴露在使用类4或5(在接触地面,淡水或海水).实验室方法
简介：This Technical Specification specifies a laboratory method for obtaining water samples from treated wood
信息：ICS：13.020.30;71.100.50 CCS：发布：2012 实施：

ISO 23977-2-2020 塑料.暴露于海水中的塑料材料需氧生物降解的测定.第2部分:用密闭呼吸计测量需氧量的方法
简介：
信息：ICS：83.080.01 CCS：发布：0000-00-00 实施：0000-00-00

ASTM G52-00(2011) 表面海水中金属和合金的暴露和评估标准实践
简介：
信息：ICS：77.060 CCS：发布：2011-11-01 实施：

BS DD CEN/TS 15119-2-2008 木材和木材产品的耐久性.经过防腐剂处理的木材向环境排放物的测定.暴露在使用等级4级或5级的木制商品(与地面、淡水或海水的有关).实验室法
简介：This Technical Specification specifies a laboratory method for obtaining water samples from treated woodwhich has been in conditions designated to simulate continuous contact with the ground or with water (UseClass 4 or 5), at time intervals after exposure.
信息：ICS：13.020.30;71.100.50 CCS：B71 发布：2010-02-28 实施：2010-02-28

KS D ISO 11306-2009 金属和合金的腐蚀.暴露在海水表面的金属和合金的评定导则
简介：1.1 이 표준은 금속 및 합금을 바닷물 표면에 폭로시켜 위치의 차이에 따라 비교를 하고자
信息：ICS：77.060 CCS：H25 发布：2009-10-06 实施：2009-10-06

北检院部分仪器展示

北检仪器展示