仪器化冲击检测标准

发布时间：2023-02-08 04:36:05

作者：北检院

阅读次数：

CNAS认证

CMA认证

ISO认证

AAA诚信企业

仪器化冲击检测标准相关标准参考信息

GB/T 32065.11-2021 海洋仪器环境试验方法第11部分：冲击与碰撞试验
简介：
信息：ICS：19.040 CCS：A21 发布：2021-12-31 00:00:00.0 实施：2022-07-01 00:00:00.0

DIN EN ISO 14556-2016 金属材料.夏比V形切痕摆式冲击试验.仪器试验法(ISO 14556-2015);德文版本EN ISO 14556-2015
简介：
信息：ICS：77.040.10 CCS：H22 发布：2016-02 实施：

ASTM E2298-2013 金属材料仪器化冲击试验的标准试验方法
简介：5.1x00a0;Instrumented impact testing provides an independent measurement of the total absorbed energy associated with fracturing CVN or MCVN specimens for test machines equipped with a dial and/or optical encoder. 5.2x00a0;Instrumented impact testing is particularly effective in MCVN testing since the resolution of a calibrated strain-gaged striker does not necessarily decrease with the magnitude of the measured energy. 5.3x00a0;In addition to providing an measure of total absorbed energy (Wt), instrumented testing enables the determination of characteristic force, energy, and displacement parameters. Depending on the material and test temperature, these parameters can provide very useful information (in addition to total absorbed energy) on the fracture behavior of materials such as: the temperature which corresponds to the onset of the lower shelf; the temperature which corresponds to the onset of the upper shelf; the pre-maximum force energy (Wm); the post-maximum force energy; the energy associated with shear lip tearing after brittle fracture; the general yield force (Fgy); the force at brittle fracture initiation (Fbf); the arrest force (Fa). The instrumented data may also be used to highlight test results which should be discarded on the basis of misalignment or other critical test factors. 1.1x00a0;This test method establishes the requirements for performing instrumented Charpy V-Notch (CVN) and instrumented Miniaturized Charpy V-Notch (MCVN) impact tests on metallic materials. This method, which is based on experience developed testing steels, provides further information (in addition to the total absorbed energy) on the fracture behavior of the tested materials. Minimum requirements are given for measurement and recording equipment such that similar sensitivity and comparable total absorbed energy measurements to those obtained in Test Methods E23 and E2248 are achieved. 1.2x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.040.10 (Mechanical testing of metals) CCS：H22 发布：2013 实施：

GB/T 19748-2019 金属材料夏比V型缺口摆锤冲击试验仪器化试验方法
简介：
信息：ICS：77.040.10 CCS：H22 发布：2019-08-30 00:00:00.0 实施：2020-07-01 00:00:00.0

KS M ISO 179-2-2012 塑料.摆锤式冲击特性的测定.第2部分:仪器冲击试验
简介：1.1 이 표준은 플라스틱의 힘-변형 그래프에서 샤르피 충격 강도 측정 방법에 대하여 규정
信息：ICS：83.080.01 CCS：G31 发布：2012-12-22 实施：2012-12-22

GB/T 1043.2-2018 塑料简支梁冲击性能的测定第2部分：仪器化冲击试验
简介：
信息：ICS：83.080.01 CCS：G31 发布：2018-03-15 00:00:00.0 实施：2018-10-01 00:00:00.0

BS EN ISO 14556-2015 金属材料.夏比V形切口摆式冲击试验.仪器试验法
简介：
信息：ICS：77.040.10 CCS：H11 发布：2015-10-31 实施：2015-10-31

KS M ISO 179-1-2012(2017) 塑料夏比冲击性能的测定第1部分:非仪器冲击试验
简介：
信息：ICS：83.080.01 CCS：发布：2012-12-22 实施：

GB/T 1043.1-2008 塑料.简支梁冲击性能的测定.第1部分:非仪器化冲击试验
简介：GB/T 1043的本部分规定了塑料在规定条件下测定简支梁冲击强度的方法。规定了几种不同类型的试样与试验。根据材料类型、试样类型和缺口类型规定了不同的试验参数。本部分用于研究规定类型的试样在规定冲击条件下的行为和评估试样在试验条件下的脆性和韧性，也可用于同类材料可比数据的测定。本部分适用于下列范围的材料:—硬质热塑性模塑和挤塑材料，包括经填充和增强的材料，硬质热塑性板材； —硬质热固性模塑材料，包括经填充和增强的材料，硬质热固性板材，包括层压材料；—纤维单向或多向增强热固性和热塑性复合材料，如毡、织物、纺织粗纱、短切原丝、复合增强材料、无捻粗纱和磨碎纤维、预浸渍材料制成的片材（预浸料坯），包括经填充和增强的材料；—热致液晶聚合物。本部分不适用于硬质泡沫材料和含有泡沫材料的夹层结构材料。本部分适用于规定尺寸的模塑试样和自标准多用途试样（见GB/T 11997）的中部经机加工制成的试样，或由成品、半成品，如模塑制品、层压板、挤出或浇铸板材经机加工的试样。本部分规定了试样的优选尺寸。用不同尺寸和缺口的试样以及不同条件下制备的试样进行试验时，其结果是不可比的。本部分不应作为设计的依据。但在不同温度下的试验、改变缺口半径和/或厚度以及在不同条件下制备试样，可以获得材料的典型性能资料。
信息：ICS：83.140 CCS：G32 发布：2008-08-04 实施：2009-04-01

BS EN ISO 14556-2015 金属材料.夏比V形切口摆式冲击试验.仪器试验法
简介：
信息：ICS：77.040.10 CCS：H11 发布：2015-10-31 实施：2015-10-31

KS M ISO 179-2-2012(2022) 塑料夏比冲击性能的测定第2部分:仪器冲击试验
简介：
信息：ICS：83.080.01 CCS：发布：2012-12-22 实施：

GB/T 19748-2005 钢材夏比V型缺口摆锤冲击试验仪器化试验方法
简介：本标准规定了钢材夏比V型缺口摆锤冲击试验仪器化试验方法的原理、术语及定义、试样、试验设备及仪器、试验步骤、试验结果评定和处理及试验报告。本标准适用于钢的夏比V型缺口试样。经协商，本标准也可用于其他金属材料和U型缺口试样的试验。
信息：ICS：77.040.10 CCS：H22 发布：2005-05-13 实施：2005-10-01

NF R10-212-2015 道路车辆.冲击试验的测量技术.仪器
简介：
信息：ICS：43.020 CCS：T04 发布：2015-10-30 实施：2015-10-30

KS M ISO 179-2-2012(2017) 塑料夏比冲击性能的测定第2部分:仪器冲击试验
简介：
信息：ICS：83.080.01 CCS：发布：2012-12-22 实施：

GB/T 16896.1-2005 高电压冲击测量仪器和软件第1部分;对仪器的要求
简介：本部分适用于冲击高电压和冲击大电流试验中测量用数字记录仪(包括数字示波器)，模拟示波器和峰值电压表。本部分规定了为满足GB/T 16927.2中测量不确定度和程序所要求的测量性能和校验。本部分包括： ——数字记录仪、模拟示波器和峰值电压表有关的专用术语的定义； ——对这些仪器必需的要求，以保证它们符合高电压和大电流冲击试验的要求； ——满足这些要求所必须的试验和程序。本部分仅涉及可从长期或临时的存储器中存取原始数据的数字记录仪，这些原始数据连同相关的刻度因数等资料，可以： ——打印或绘图； ——以数字形式存贮。
信息：ICS：17.220.20 CCS：L86 发布：2005-02-06 实施：2005-12-01

EN ISO 14556-2015 金属材料.夏比V型缺口摆锤冲击试验.仪器测试方法（ISO 14556:2015）
简介：Diese Internationale Norm legt den instrumentierten Kerbschlagbiegeversuch nach Charpy (V-Kerb) für metallische Werkstoffe sowie die Anforderungen an die Mess- und Aufzeichnungseinrichtungen fest. In Bezug auf den in ISO 148-1 beschriebenen Kerbschlagbiegeversuch nach Charpy ermöglicht der hier beschriebene Versuch weitergehende Aussagen über das Bruchverhalten des untersuchten Erzeugnisses unter schlagartigen Beanspruchungsbedingungen.
信息：ICS：77.040.10 CCS：H10 发布：2015-10-01 实施：

GB/T 15727-1995 实验室仪器玻璃热冲击试验方法(棒状法)
简介：本标准规定了玻璃材质的热冲击试验方法的原理、设备、试样、试验程序及结果处理。本标准适用于玻璃材质的热冲击试验。
信息：ICS：71.040.20 CCS：N64 发布：1995-10-24 实施：1996-07-01

BS ISO 6487-2012 道路车辆. 冲击试验用测量技术. 仪器
简介：
信息：ICS：43.020 CCS：T39 发布：2012-10-31 实施：2012-10-31

GB/T 16896.2-2016 高电压和大电流试验测量用仪器和软件第2部分:对冲击电压和冲击电流试验用软件的要求
简介：
信息：ICS： CCS：发布：实施：2016-09-01

ISO 14556:2015 金属材料 - 夏比V型槽口冲击试验 - 仪器测试方法
简介：
信息：ICS：77.040.10 CCS：发布：2015-09-11 实施：

NF T51-035-2/A1-2012 塑料 - 夏比冲击性能的测定 - 第2部分: 仪器化冲击试验 - 修正本1: 准确度数据.
简介：
信息：ICS：83.080.01 CCS：G31 发布：2012-06-01 实施：2012-06-23

KS C IEC 61083-1-2022 高压和大电流试验中测量用仪器和软件.第1部分:冲击试验用仪器的要求
简介：
信息：ICS： CCS：发布：2022-12-23 实施：

ISO 14556-2015 金属材料.夏比V形切痕摆式冲击试验.仪器试验法
简介：
信息：ICS：77.040.10 CCS：H22 发布：2015-09 实施：

JJF 1320-2011 仪器化夏比摆锤冲击试验机校准规范
简介：本规范适用于仪器化金属夏比摆锤冲击试验机（以下简称试验机）的校准。
信息：ICS： CCS：N75 发布：2011-11-14 实施：2012-02-14

KS M ISO 179-1-2022 塑料.夏比冲击性能的测定.第1部分:非仪器冲击试验
简介：
信息：ICS：83.080.01 CCS：发布：2022-12-19 实施：

BS ISO 6487-2015 道路车辆. 冲击试验用测量技术. 仪器
简介：
信息：ICS：43.020 CCS：T39 发布：2015-07-31 实施：2015-07-31

DIN EN ISO 179-1-2010 塑料.摆锤式冲击性能测定.第1部分:非仪器化冲击试验(ISO 179-1-2010).德文版本EN ISO 179-1-2010
简介：
信息：ICS：83.080.01 CCS：G31 发布：2010-11 实施：

ASTM D6537-00(2021) 测定包装性能的仪器化包装冲击试验的标准实施规程
简介：
信息：ICS：55.040 CCS：发布：2021-10-01 实施：

BS ISO 6487-2015 道路车辆. 冲击试验用测量技术. 仪器
简介：
信息：ICS：43.020 CCS：T39 发布：2015-07-31 实施：2015-07-31

ASTM F1702-10 使用轻便便携式仪器测量自然播放表面系统的冲击衰减特性的标准测试方法
简介：
信息：ICS：19.060 CCS：发布：2010-07-01 实施：

IEC 61083-1:2021 高压和大电流试验中测量用仪器和软件.第1部分:冲击试验用仪器的要求
简介：
信息：ICS：19.080 CCS：发布：2021-01-28 实施：

ASTM E2298-2015 金属材料仪器化冲击试验的标准试验方法
简介：5.1x00a0;Instrumented impact testing provides an independent measurement of the total absorbed energy associated with fracturing CVN or MCVN specimens for test machines equipped with a dial and/or optical encoder. 5.2x00a0;Instrumented impact testing is particularly effective in MCVN testing since the resolution of a calibrated strain-gaged striker does not necessarily decrease with the magnitude of the measured energy. 5.3x00a0;In addition to providing an measure of total absorbed energy (Wt), instrumented testing enables the determination of characteristic force, energy, and displacement parameters. Depending on the material and test temperature, these parameters can provide very useful information (in addition to total absorbed energy) on the fracture behavior of materials such as: the temperature which corresponds to the onset of the lower shelf; the temperature which corresponds to the onset of the upper shelf; the pre-maximum force energy (Wm); the post-maximum force energy; the energy associated with shear lip tearing after brittle fracture; the general yield force (Fgy); the force at brittle fracture initiation (Fbf); the arrest force (Fa). The instrumented data may also be used to highlight test results which should be discarded on the basis of misalignment or other critical test factors. 1.1x00a0;This test method establishes the requirements for performing instrumented Charpy V-Notch (CVN) and instrumented Miniaturized Charpy V-Notch (MCVN) impact tests on metallic materials. This method, which is based on experience developed testing steels, provides further information (in addition to the total absorbed energy) on the fracture behavior of the tested materials. Minimum requirements are given for measurement and recording equipment such that similar sensitivity and comparable total absorbed energy measurements to those obtained in Test Methods E23 and E2248 are achieved. 1.2x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.040.10 CCS：发布：2015 实施：

ISO 179-1:2010 塑料制品；夏比冲击性能的测定第1部分:非仪器冲击试验
简介：
信息：ICS：83.080.01 CCS：发布：2010-06-04 实施：

IEC 61083-1-2021 高压和高电流试验中测量用仪器及软件. 第1部分: 冲击试验仪器要求
简介：This part of IEC 61083 is applicable to digital recorders, including digital oscilloscopes, used for measurements during tests with high impulse voltages and high impulse currents. It specifies the measuring characteristics and calibrations required to meet the measuring uncertai
信息：ICS：17.220.20 CCS：N23 发布：2021-01-00 实施：

SAE J211-2-2014 冲击试验用仪器.第2部分:摄影仪器
简介：The purpose of this SAE Recommended Practice is to define criteria of performance for an optical data channel when numerical time and space data are taken from the images to analyze impact test results.
信息：ICS：19.060;43.180 CCS：R17 发布：2014-06-16 实施：

EN ISO 179-1-2010 塑料.摆锤冲击特性测定.第1部分:非仪器冲击试验
简介：This part of ISO 179 specifies a method for determining the Charpy impact strength of plastics under defined conditions. A number of different types of specimen and test configurations are defined. Different test parameters are specified according to the type of material, the type of test specimen and the type of notch
信息：ICS：83.080.01 CCS：发布：2010-06-01 实施：

IEC 61083-3-2020 高压和高电流冲击试验中测量用仪器和软件. 第3部分: 交流和直流电压和电流试验用硬件的要求
简介：This part of IEC 61083 is applicable to digital recording instruments used for measurements during tests with high alternating and direct voltages and currents. It specifies the measuring characteristics and calibrations required to meet the measuring uncertainties and procedures
信息：ICS：17.220.20 CCS：N23 发布：2020-11-00 实施：

ASTM D6537-00(2014) 用于测试封装性能的仪器封装冲击测试的标准实践
简介：
信息：ICS：55.040 CCS：发布：2014-04-01 实施：

ASTM E2298-2009 金属材料的仪器化冲击试验的标准试验方法
简介：Instrumented impact testing provides an independent measurement of the total absorbed energy associated with fracturing CVN or MCVN specimens for test machines equipped with a dial and/or optical encoder. Instrumented impact testing is particularly effective in MCVN testing since the resolution of a calibrated strain-gaged striker does not necessarily decrease with the magnitude of the measured energy. In addition to providing an measure of total absorbed energy (Wt), instrumented testing enables the determination of characteristic force, energy, and displacement parameters. Depending on the material and test temperature, these parameters can provide very useful information (in addition to total absorbed energy) on the fracture behavior of materials such as: the temperature which corresponds to the onset of the lower shelf; the temperature which corresponds to the onset of the upper shelf; the pre-maximum force energy (Wm); the post-maximum force energy; the energy associated with shear lip tearing after brittle fracture; the general yield force (Fgy); the force at brittle fracture initiation (Fbf); the arrest force (Fa). The instrumented data may also be used to highlight test results which should be discarded on the basis of misalignment or other critical test factors.1.1 This standard establishes the requirements for performing instrumented Charpy V-Notch (CVN) and instrumented Miniaturized Charpy V-Notch (MCVN) impact tests on metallic materials. This method, which is based on experience developed testing steels, provides further information (in addition to the total absorbed energy) on the fracture behavior of the tested materials. Minimum requirements are given for measurement and recording equipment such that similar sensitivity and comparable total absorbed energy measurements to those obtained in Test Methods E 23 and E 2248 are achieved. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.040.10 (Mechanical testing of metals) CCS：H22 发布：2009 实施：

ISO 179-2:2020 塑料 - 夏比冲击性能的测定 - 第2部分:仪器冲击试验
简介：
信息：ICS：83.080.01 CCS：发布：2020-05-14 实施：

SAE J211-1-2014 冲击试验仪器装置.第1部分:电子仪器装置
简介：This recommended practice outlines a series of performance recommendations, which concern the whole data channel. These recommendations are not subject to any variation and all of them shall be adhered to by any agency conducting tests to this practice. However, the method of demonstrating compliance with the recommendations is flexible and can be adapted to suit the needs of the particular equipment the agency is using. It is not intended that each recommendation be taken in a literal sense, as necessitating a single test to demonstrate that the recommendation is met. Rather, it is intended that any agency proposing to conduct tests to this practice shall
信息：ICS：19.060;43.180 CCS：N73 发布：2014-03-31 实施：

GOST R 53655.2-2009 塑料薄膜与薄板.利用自由落体重量法测定抗冲击性.第2部分:仪器冲击试验
简介：
信息：ICS：83.140.10 CCS：发布：2009 实施：2011-01-01

JB/T 13810-2020 仪器化夏比摆锤冲击试验机
简介：
信息：ICS：19.059999999999999 CCS：N73 发布：2020-04-16 实施：2021-01-01

DIN EN 61083-2-2013 高压和高电流冲击试验中测量用仪器和软件. 第2部分:电压和电流冲击试验用软件的要求 (IEC 61083-2-2013); 德文版本EN 61083-2-2013, 带有CD-ROM
简介：
信息：ICS：17.220.20;35.240.50 CCS：N73 发布：2013-12 实施：2013-12-01

ISO 6487 AMD 1-2008 道路车辆.冲击试验测量技术.仪器.修改件1
简介：ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies(ISO member bodies). The work of preparing International Standards is normally carried out through ISOtechnical committees. Each member body interested in a subject for which a technical committee has beenestablished has the right to be represented on that committee. International organizations, governmental andnon-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with theInternational Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standardsadopted by the technical committees are circulated to the member bodies for voting. Publication as anInternational Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patentrights. ISO shall not be held responsible for identifying any or all such patent rights.Amendment 1 to ISO6487:2002 was prepared by Technical Committee ISO/TC22, Road vehicles,Subcommittee SC 12, Passive safety crash protection systems.
信息：ICS：43.020 CCS：T39 发布：2008-07-15 实施：

ASTM F1702-10(2018) 使用轻便便携式仪器测量自然播放表面系统的冲击衰减特性的标准测试方法
简介：
信息：ICS：19.060 CCS：发布：2018-12-01 实施：

NF C41-108-2013 高压和高电流冲击试验中测量用仪器和软件 - 第2部分: 电压和电流冲击试验用软件的要求
简介：
信息：ICS：17.220.20;35.240.50 CCS：N73 发布：2013-09-21 实施：2013-09-21

ISO 6487-2002/Amd 1-2008 道路车辆.冲击试验中的测量技术.仪器.修改件1:
简介：
信息：ICS：43.020 CCS：发布：2008-07-10 实施：

ISO 6487-2015/Amd 1-2017 道路车辆.冲击试验中的测量技术.仪器.修改件1
简介：
信息：ICS：43.020 CCS：发布：2017-10-02 实施：

BS EN 61083-2-2013 高压和高电流试验中测量用仪器和软件.电压和电流冲击试验用软件的要求
简介：
信息：ICS：17.220.20;35.080 CCS：N20 发布：2013-07-31 实施：2013-07-31

GOST R 53190-2008 机械、仪器和其他物品的环境动态试验.带有冲击响应谱合成的冲击试验
简介：
信息：ICS：19.040 CCS：A21;K04 发布：2008 实施：2010-01-01

DIN EN ISO 14556-2017 金属材料.夏比V形切痕摆式冲击试验.仪器试验法(ISO 14556-2015);德文版本EN ISO 14556-2015
简介：
信息：ICS：77.040.10 CCS：H22 发布：2017-05 实施：

IEC 61083-2-2013 高压和高电流冲击试验中测量用仪器和软件.第2部分:电压和电流冲击试验用软件的要求
简介：
信息：ICS：17.220.20;19.080;35.080 CCS：N22 发布：2013-03 实施：

JIS K7111-2-2006 塑料.摆锤冲击特性的测定.第2部分:用仪器装备的冲击试验
简介：1.1この規格は，衝撃力—たわみ線図からプラスチックのシャルピー衝撃特性を求める方法について規定する。…
信息：ICS：83.080.01 CCS：G31 发布：2006-12-20 实施：2006-12-20

KS R ISO 6487-2017(2022) 道路车辆.最小冲击试验测量技术.仪器
简介：
信息：ICS：43.020 CCS：发布：2017-01-16 实施：

ASTM E2298-2013a 金属材料仪器化冲击试验的标准试验方法
简介：5.1x00a0;Instrumented impact testing provides an independent measurement of the total absorbed energy associated with fracturing CVN or MCVN specimens for test machines equipped with a dial and/or optical encoder. 5.2x00a0;Instrumented impact testing is particularly effective in MCVN testing since the resolution of a calibrated strain-gaged striker does not necessarily decrease with the magnitude of the measured energy. 5.3x00a0;In addition to providing an measure of total absorbed energy (Wt), instrumented testing enables the determination of characteristic force, energy, and displacement parameters. Depending on the material and test temperature, these parameters can provide very useful information (in addition to total absorbed energy) on the fracture behavior of materials such as: the temperature which corresponds to the onset of the lower shelf; the temperature which corresponds to the onset of the upper shelf; the pre-maximum force energy (Wm); the post-maximum force energy; the energy associated with shear lip tearing after brittle fracture; the general yield force (Fgy); the force at brittle fracture initiation (Fbf); the arrest force (Fa). The instrumented data may also be used to highlight test results which should be discarded on the basis of misalignment or other critical test factors. 1.1x00a0;This test method establishes the requirements for performing instrumented Charpy V-Notch (CVN) and instrumented Miniaturized Charpy V-Notch (MCVN) impact tests on metallic materials. This method, which is based on experience developed testing steels, provides further information (in addition to the total absorbed energy) on the fracture behavior of the tested materials. Minimum requirements are given for measurement and recording equipment such that similar sensitivity and comparable total absorbed energy measurements to those obtained in Test Methods E23 and E2248 are achieved. 1.2x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.040.10 (Mechanical testing of metals) CCS：H22 发布：2013 实施：

JIS K7111-1-2006 塑料.摆锤冲击特性的测定.第1部分:无仪器装备的冲击试验
简介：1.1この規格は，定められた条件下でのプラスチックのシャルピー衝撃強さを求める方法について規定する。…
信息：ICS：83.080.01 CCS：G31 发布：2006-12-20 实施：2006-12-20