动态撕裂检测标准

动态撕裂检测标准相关标准参考信息

GB/T 5482-2007 金属材料动态撕裂试验方法
简介：本标准规定了金属材料动态撕裂试验试样及其制备、试验机、测试方法和试验结果的处理。 本标准适用于测定洛氏硬度值小于36HRC的金属材料或焊接接头试样的动态撕裂能和纤维断面率。
信息：ICS：77.040.10 CCS：H22 发布：2007-02-09 实施：2007-08-01

ANSI/ASTM E604-1983 金属材料动态撕裂试验方法
简介：This test method covers the dynamic tear (DT) test using specimens that are 3/16 in. to 5/8 in. (5 mm to 16 mm) inclusive in thickness. This test method is applicable to materials with a minimum thickness of 3/16 in. (5 mm). The pressed-knife procedure described for sharpening the notch tip generally limits this test method to materials with a hardness level less than 36 HRC. Note 1 -The designation 36 HRC is a Rockwell hardness number of 36 on Rockwell C scale as defined in Test Methods E 18.
信息：ICS：77.040.10 CCS：H23 发布：1983 实施：1999-02-18

简介： 信息：

GB/T 20654-2006 防护服装 机械性能 材料抗刺穿及动态撕裂性的试验方法
简介：本标准规定了防护服装材料抗刺穿及动态撕裂性的试验方法。这种刺穿和撕裂会损伤服装或因服装的完整性被破坏而对穿着者产生伤害。当发生意外伤害的风险与刺穿和撕裂的程度相关时，确定其性能级别就可以规定要使用的材料。
信息：ICS：13.340.10 CCS：C73 发布：2006-12-07 实施：2007-07-01

ASTM E604-1983(2008) 金属材料动态撕裂的标准试验方法
简介：The DT energy value is a measure of resistance to rapid progressive fracturing. In a number of applications, the enhanced resistance that may develop during about one plate thickness of crack extension from a sharp notch is of major interest. In the test method, a sufficiently long fracture path is provided so that the results serve as a measure of this property. Fracture surfaces of nonaustenitic steels tested in their temperature transition region have areas that appear bright and areas that appear dull. The bright, faceted appearing areas are termed x201C;cleavagex201D; fracture, and the dull appearing areas are termed x201C;shearx201D; fracture after their respective mode of fracture on a micro scale. This test method can serve the following purposes: In research and development, to evaluate the effects of metallurgical variables such as composition, processing, or heat treatment, or of fabricating operations such as forming and welding on the dynamic tear fracture resistance of new or existing materials. In service evaluation, to establish the suitability of a material for a specific application only where a correlation between DT energy and service performance has been established. For information, specifications of acceptance, and manufacturing quality control when a minimum DT energy is requested. Detailed discussion of the basis for determining such minimum values in a particular case is beyond the scope of this test method.1.1 This test method covers the dynamic tear (DT) test using specimens that are 3/16 in. to 5/8 in. (5 mm to 16 mm) inclusive in thickness. 1.2 This test method is applicable to materials with a minimum thickness of 3/16 in. (5 mm). 1.3 The pressed-knife procedure described for sharpening the notch tip generally limits this test method to materials with a hardness level less than 36 HRC. Note 18212;The designation 36 HRC is a Rockwell hardness number of 36 on Rockwell C scale as defined in Test Methods E 18. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.040.10 (Mechanical testing of metals) CCS：H22 发布：1983 实施：

简介： 信息：

GB 5482-1993 金属材料动态撕裂试验方法
简介：
信息：ICS：77.040 CCS：U05 发布：1993-01-03 实施：1993-10-01

CSN 42 0340-1982 金属材料的动态撕裂能的标准测试方法
简介：Zpracovatel: Státní v?zkumn? ústav materiálu, Praha — Ing. Franti?ek Ilajsk?Vedoucí oborové normaliza?ní st?edisko: Státní v?zkumn? ústav materiálu, Praha — íng. Ji?í DokoupilPracovník ??adu pro normalizaci a mě?ení: Tng. P?emysl Berounsk?
信息：ICS：77.040.10 CCS： 发布：1982-8-13 实施：

简介： 信息：

GB/T 5482-1993 金属材料动态撕裂试验方法
简介：本标准规定了金属材料动态撕裂试验试样及其制备、试验机、测试方法和试验结果的处理。 本标准适用于测定洛氏硬度值小于HRC36的金属材料或焊接接头试样的动态撕裂能和纤维断面率。
信息：ICS：77.040.10 CCS：H22 发布：1985-10-17 实施：1993-10-01

简介： 信息：

简介： 信息：

ASTM E604-18 金属材料动态撕裂试验的标准试验方法
简介：
信息：ICS：77.040.10 CCS： 发布：2018-06-01 实施：

简介： 信息：

简介： 信息：

ASTM E604-15 金属材料动态撕裂试验的标准试验方法
简介：
信息：ICS：77.040.10 CCS： 发布：2015-12-01 实施：

简介： 信息：

简介： 信息：

ASTM E604-2015 金属材料的动态撕裂试验的标准试验方法
简介：5.1x00a0;The DT energy value is a measure of resistance to rapid progressive fracturing. In a number of applications, the enhanced resistance that may develop during about one plate thickness of crack extension from a sharp notch is of major interest. In the test method, a sufficiently long fracture path is provided so that the results serve as a measure of this property. 5.2x00a0;Fracture surfaces of nonaustenitic steels tested in their temperature transition region have areas that appear bright and areas that appear dull. The bright, faceted appearing areas are termed x201c;cleavagex201d; fracture, and the dull appearing areas are termed x201c;shearx201d; fracture after their respective mode of fracture on a micro scale. 5.3x00a0;This test method can serve the following purposes: 5.3.1x00a0;In research and development, to evaluate the effects of metallurgical variables such as composition, processing, or heat treatment, or of fabricating operations such as forming and welding on the dynamic tear fracture resistance of new or existing materials. 5.3.2x00a0;In service evaluation, to establish the suitability of a material for a specific application only where a correlation between DT energy and service performance has been established.3 5.3.3x00a0;For information, specifications of acceptance, and manufacturing quality control when a minimum DT energy is requested. Detailed discussion of the basis for determining such minimum values in a particular case is beyond the scope of this test method. 1.1x00a0;This test method covers the dynamic tear (DT) test using specimens that are 3/16x00a0;in. to 5/8x00a0;in. (5 mm to 16 mm) inclusive in thickness. 1.2x00a0;This test method is applicable to materials with a minimum thickness of 3/16x00a0;in. (5 mm). 1.3x00a0;The pressed-knife procedure described for sharpening the notch tip generally limits this test method to materials with a hardness level less than 36 HRC. Note 1:x00a0;The designation 36 HRC is a Rockwell hardness number of 36 on Rockwell C scale as defined in Test Methods E18. 1.4x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.040.10 CCS： 发布：2015 实施：

简介： 信息：

简介： 信息：

KS K ISO 13995-2008(2018) 防护服机械性能材料抗穿刺和动态撕裂的试验方法
简介：
信息：ICS：13.340.10 CCS： 发布：2008-12-23 实施：

简介： 信息：

简介： 信息：

ASTM E604-83(2008) 金属材料动态撕裂试验的标准试验方法
简介：
信息：ICS：77.040.10 CCS： 发布：2008-09-01 实施：

简介： 信息：

简介： 信息：

JIS T8050-2005 防护服.机械特性.测定材料抗刺穿和动态撕裂的试验方法
简介：この規格は，衣服にかぎ裂及び引裂によって許容限度を超える被害が及ぶか，又はバリアの完全性が失われる結果，衣服着用者に危険が及ぶ可能性のある状況下で使用する防護服の材料に対し，突刺及び動的引裂に対する抵抗性の試験方法について規定する。
信息：ICS：13.340.10 CCS：C73 发布：2005-12-25 实施：

简介： 信息：

简介： 信息：

NF S74-546-2001 防护服.机械性能.抗穿刺性和抗动态撕裂性测定的试验方法
简介：
信息：ICS：13.340.10 CCS：C73 发布：2001-04-01 实施：2001-04-05

简介： 信息：

简介： 信息：

DIN EN ISO 13995-2001 防护服.机械性能.抗刺穿和动态撕裂材料试验方法
简介：
信息：ICS：13.340.10 CCS：C73 发布：2001-03 实施：2001-03-01

简介： 信息：

简介： 信息：

BS EN ISO 13995-2001 防护服.机械特性.测定服装材料抗穿孔性和抗动态撕裂的测试方法
简介：This European Standard specifies a test method for the determination of the resistance to puncture and dynamic tearing of protective clothing materials which are used in situations where snagging and tearing could result in unacceptable damage to the clothing or danger to the wearer through loss of integrity of a barrier. It is intended that the performance levels determined will be of use in specifying materials for use in situations where the risk of harm is related to the size of puncture and tear that may occur in accidents.
信息：ICS：13.340.10 CCS：C73 发布：2001-02-15 实施：2001-02-15

简介： 信息：

简介： 信息：

ISO 13995-2000 防护服 机械特性 测定服装材料抗穿孔性和动态撕裂力的试验方法
简介：This European Standard specifies a test method for the determination of the resistance to puncture and dynamic tearing of protective clothing materials which are used in situations where snagging and tearing could result in unacceptable damage to the clothing or danger to the wearer through loss of integrity of a barrier. It is intended that the performance levels determined will be of use in specifying materials for use in situations where the risk of harm is related to the size of puncture and tear that may occur in accidents.
信息：ICS：13.340.10 CCS：C73 发布：2000-12 实施：

简介： 信息：

简介： 信息：

ISO 13995:2000 防护服——机械性能——测定材料抗穿刺性和动态撕裂性的试验方法
简介：
信息：ICS：13.340.10 CCS： 发布：2000-11-30 实施：

简介： 信息：

简介： 信息：

TB/T 2985-2000 金属材料的动态撕裂试验方法
简介：本标准规定了金属动态撕裂试验用装置、试样和试验方法。本标准适用于最小厚度为5mm的金属材料的动态撕裂试验。
信息：ICS： CCS：S04 发布：2000-03-29 实施：2000-11-01

简介： 信息：

简介： 信息：

EN ISO 13995-2000 防护服.机械性能.抗穿刺性和抗动态撕裂性测定的试验方法 ISO 13995-2000
简介：
信息：ICS：13.340.10 CCS： 发布：2000 实施：

简介： 信息：

简介： 信息：

ASTM E604-83(1994) 金属材料动态撕裂试验的标准试验方法
简介：
信息：ICS： CCS： 发布：1994-01-01 实施：

简介： 信息：

简介： 信息：

ASTM E604-83(2002) 金属材料动态撕裂试验的标准试验方法
简介：
信息：ICS：77.040.10 CCS： 发布：1983-03-25 实施：

简介： 信息：

简介： 信息：

ASTM E604-83 金属材料动态撕裂试验的标准试验方法
简介：
信息：ICS： CCS： 发布：1983-01-01 实施：

简介： 信息：

简介： 信息：