应力疲劳检测标准

应力疲劳检测标准相关标准参考信息

GB/T 1687.4-2021 硫化橡胶 在屈挠试验中温升和耐疲劳性能的测定 第4部分：恒应力屈挠试验
简介：
信息：ICS：83.060 CCS：G40 发布：2021-10-11 00:00:00.0 实施：2022-05-01 00:00:00.0

BS 7270-2006 金属材料.控制轴向疲劳的恒定振幅应力.试验方法
简介：This British Standard describes a method of cyclically loading a metallic specimen under strain control between set strain limits to determine its fatigue resistance. The fatigue resistance is measured in terms of cycles to failure as a function of the applied strain range and the associated variations in stress range, mean stress and plastic strain range. The method is restricted to uniaxially loaded parallel section specimens tested in air at ambient temperature and to metals where time-dependent deformation can be ignored. The method is applicable to both high- and low-cycle fatigue tests.
信息：ICS：77.040.10 CCS：H22 发布：2006-12-29 实施：2006-12-29

SIS SS 11 23 73-1979 金属材料．扭转应力疲劳试验．试样设计
简介：
信息：ICS： CCS： 发布：1979-7-1 实施：

GB/T 35465.2-2017 聚合物基复合材料疲劳性能测试方法 第2部分：线性或线性化应力寿命（S-N）和应变寿命（ε-N）疲劳数据的统计分析
简介：
信息：ICS：83.120 CCS：Q23 发布：2017-12-29 00:00:00.0 实施：2018-11-01 00:00:00.0

ASTM E739-91(2004)e1 线性或线性化应力寿命（S-N）和应变寿命（&949-N）疲劳数据
简介：
信息：ICS：19.060 CCS： 发布：2006-05-01 实施：

ISO 1352:1977 钢.扭转应力疲劳试验
简介：
信息：ICS：77.040.10 CCS： 发布：1977-12-01 实施：

GB/Z 32332.2-2015 滚动轴承　对ISO 281的注释　第2部分：基于疲劳应力系统方法的修正额定寿命计算
简介：
信息：ICS：21.100.20 CCS：J11 发布：2015-12-31 实施：2016-04-01

ASTM E739-91(2004) 线性或线性化应力寿命（S-N）和应变寿命（&949- N）疲劳数据
简介：
信息：ICS： CCS： 发布：2004-05-01 实施：

ISO 1352-1977 钢 扭转应力疲劳试验
简介：The tests are carried out at room temperature, in air, by applying to the test piece a pure couple about its longitudinal axid. Test piece diameters are between 5 mm and 12,5 mm. The proparation, form and testing of test pieces of circular cross-section are specified. Does not specify component testing and high strain torsional fatigue tests, which lead to failure in a few thousand cycles.
信息：ICS：77.040.10 CCS：H22 发布：1977-12 实施：

GB/T 12443-2007 金属材料 扭应力疲劳试验方法
简介：本标准规定了金属材料扭应力疲劳试验的原理、术语、符号、试样、试验机、试验条件、试验程序、试验结果的表示方法和试验报告 本标准适用于室温大气下，测定公称直径为5.0 mm～12.5 mm圆形横截面金属光滑试样的扭应力疲劳性能 注：做腐蚀环境下的金属扭应力疲劳试验时，可参照GB/T 7733中4.2条的规定
信息：ICS： CCS：H22 发布：2007-11-23 实施：2008-06-01

ASME SEC III D1 MA APP I-2002 附录I.设计应力强度值、允许应力、材料性能和设计疲劳曲线
简介：Boiler and Pressure Vessel. Appendix I Design Stress Intensity Values, Allowable Stresses, Material Properties, and Design Fatigue Curves
信息：ICS： CCS：F69 发布：2002-07-01 实施：

NF T46-021-1973 橡胶和类似的合成橡胶.用重复拉应力法测定动力的疲劳试验
简介：
信息：ICS：83.060 CCS：G34 发布：1973-09-01 实施：1973-09-15

GB/T 12443-1990 金属扭应力疲劳试验方法
简介：本标准规定了金属扭应力疲劳试验的原理、术语、符号、试样、试验机、试验条件、试验程序、试验结果的表示方法和试验报告。 本标准适用于室温大气下，测定公称直径为5.0～12.5mm圆形横截面金属光滑试样的扭应力疲劳性能。 注：作腐蚀环境下的金属扭应力疲劳试验时，可参照GB7733中4.2条的规定。
信息：ICS：77.040.10 CCS：H22 发布：1990-07-21 实施：1991-07-01

KS B ISO 1352-2002(2012) 钢扭转应力疲劳试验
简介：
信息：ICS：77.040.10 CCS： 发布：2002-06-29 实施：

NASA-TN-D-5390-1969 应力比对7075-T6和2024-T3铝合金样品疲劳裂缝扩展的影响
简介：
信息：ICS： CCS： 发布：1969-01-01 实施：

KS M ISO 4666-4-2020 橡胶 硫化 - 测定温度上升和耐疲劳疲劳测试 - 第4部分:恒应力挠度计
简介：
信息：ICS：83.060 CCS： 发布：2020-03-11 实施：

ASTM E2207-2002 带有薄壁管状样品的应力控制轴向扭曲疲劳检验的标准实施规程
简介：Multiaxial forces often tend to introduce deformation and damage mechanisms that are unique and quite different from those induced under a simple uniaxial loading condition. Since most engineering components are subjected to cyclic multiaxial forces it is necessary to characterize the deformation and fatigue behaviors of materials in this mode. Such a characterization enables reliable prediction of the fatigue lives of many engineering components. Axial-torsional loading is one of several possible types of multiaxial force systems and is essentially a biaxial type of loading. Thin-walled tubular specimens subjected to axial-torsional loading can be used to explore behavior of materials in two of the four quadrants in principal stress or strain spaces. Axial-torsional loading is more convenient than in-plane biaxial loading because the stress state in the thin-walled tubular specimens is constant over the entire test section and is well-known. This practice is useful for generating fatigue life and cyclic deformation data on homogeneous materials under axial, torsional, and combined in- and out-of-phase axial-torsional loading conditions.1.1 The standard deals with strain-controlled, axial, torsional, and combined in- and out-of-phase axial torsional fatigue testing with thin-walled, circular cross-section, tubular specimens at isothermal, ambient and elevated temperatures. This standard is limited to symmetric, completely-reversed strains (zero mean strains) and axial and torsional waveforms with the same frequency in combined axial-torsional fatigue testing. This standard is also limited to thin-walled tubular specimens (machined from homogeneous materials) and does not cover testing of either large-scale components or structural elements.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：19.060 (Mechanical testing) CCS：H23 发布：2002 实施：

BS 3518-3-1963 疲劳试验方法.第3部分:直接应力疲劳试验
简介：Describes the procedure for carrying out direct stress fatigue tests on test pieces without deliberately introduced stress concentrations. Recommendations on the form and size of test pieces and details concerning their preparation are included together with the procedure to be carried out for obtaining fatigue properties.
信息：ICS：77.040.10 CCS：H22 发布：1963-04-16 实施：1963-04-16

ISO 4666-4:2018 橡胶 硫化 - 挠度计测试中温升和耐疲劳性的测定 - 第4部分:恒应力屈服计
简介：
信息：ICS：83.060 CCS： 发布：2018-09-18 实施：

CNS 9799-2001 压力容器之应力解析及疲劳解析
简介：本标准适用于 CNS 9788 〔压力容器（通则）〕第 3 节级分类之第一种容器之应力解析及疲劳解析。备考：1. 本标准虽以第一种容器为适用范围但对第二种、第三种容器其为特殊构造，而不能适用 CNS 9788 规定之第二种容器及第三容器之强度算之容器或容器之部分亦可适用。2. 本标
信息：ICS：23.020.10 CCS： 发布：2001-06-08 实施：2001-06-08

NASA-TN-D-960-1961 变换的应力幅值对两个铝合金中疲劳裂缝扩展比率的影响
简介：
信息：ICS： CCS： 发布：1961-01-01 实施：

KS B 6728-2015(2020) 压力容器的应力和疲劳分析
简介：
信息：ICS：23.020.30 CCS： 发布：2015-12-21 实施：

DIN 743-2-2000 轴类.负载能力的计算.第2部分:理论应力集中因素和疲劳缺口因素
简介：The document indicates the necessary influence factors for the calculation of the component fatique strength according to DIN 743-1.
信息：ICS：21.120.10 CCS：J19 发布：2000-10 实施：

NASA NACA-TN-2924-1953 带有叠加平均应力和可缩性更正的76S-T61铝合金的联合应力疲劳强度
简介：
信息：ICS： CCS： 发布：1953-01-01 实施：

ASTM E2207-2015 带有薄壁管状试样的应力控制轴向扭转疲劳试验的标准实施规程
简介：4.1x00a0;Multiaxial forces often tend to introduce deformation and damage mechanisms that are unique and quite different from those induced under a simple uniaxial loading condition. Since most engineering components are subjected to cyclic multiaxial forces it is necessary to characterize the deformation and fatigue behaviors of materials in this mode. Such a characterization enables reliable prediction of the fatigue lives of many engineering components. Axial-torsional loading is one of several possible types of multiaxial force systems and is essentially a biaxial type of loading. Thin-walled tubular specimens subjected to axial-torsional loading can be used to explore behavior of materials in two of the four quadrants in principal stress or strain spaces. Axial-torsional loading is more convenient than in-plane biaxial loading because the stress state in the thin-walled tubular specimens is constant over the entire test section and is well-known. This practice is useful for generating fatigue life and cyclic deformation data on homogeneous materials under axial, torsional, and combined in- and out-of-phase axial-torsional loading conditions. 1.1x00a0;The standard deals with strain-controlled, axial, torsional, and combined in- and out-of-phase axial torsional fatigue testing with thin-walled, circular cross-section, tubular specimens at isothermal, ambient and elevated temperatures. This standard is limited to symmetric, completely-reversed strains (zero mean strains) and axial and torsional waveforms with the same frequency in combined axial-torsional fatigue testing. This standard is also limited to characterization of homogeneous materials with thin-walled tubular specimens and does not cover testing of either large-scale components or structural elements. 1.2x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：19.060 CCS： 发布：2015 实施：

DD ENV 12936-1998 羽毛和羽绒.恒定负荷动态疲劳应力下永久变形的测定
简介：
信息：ICS：59.040 CCS：B45 发布：1998-06-15 实施：1998-06-15

简介： 信息：

DIN 743-4-2012 轴和柄负载能力的计算.第4部分:疲劳极限、持久极限.等效破坏连续应力
简介：
信息：ICS：21.120.10 CCS：J10 发布：2012-12 实施：

ASTM E739-91(1998) 线性或线性应力寿命（S-N）和应变寿命（e-N）疲劳数据的统计分析的标准实施规程
简介：
信息：ICS：19.060 CCS： 发布：1998-04-10 实施：

简介： 信息：

DIN 743-2-2012 轴和柄负载能力的计算.第2部分:理论应力集中因子和疲劳缺口因子
简介：
信息：ICS：21.120.10 CCS：J10 发布：2012-12 实施：2012-12

ANSI/ASTM E1949-1998 金属连接耐应力规环境温度疲劳寿命试验方法
简介：This test method covers a uniform procedure for the determination of strain gage fatigue life at ambient temperature. A suggested testing equipment design is included. This test method does not apply to force transducers or extensometers that use bonded resistance strain gages as sensing elements. Strain gages are part of a complex system that includes structure, adhesive, gage, leadwires, instrumentation, and (often) environmental protection. As a result, many things affect the performance of strain gages, including user technique. A further complication is that strain gages, once installed, normally cannot be reinstalled in another location. Therefore, it is not possible to calibrate individual strain gages; performance characteristics are normally presented on a statistical basis. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to its use.
信息：ICS：19.060 CCS：J04 发布：1998 实施：1999-02-18

简介： 信息：

ASTM E739-10 线性或线性化应力寿命（S-N）和应变寿命（&949-N）疲劳数据
简介：
信息：ICS：19.060 CCS： 发布：2010-11-01 实施：

NF F31-119-1995 铁路车辆.在静态应力、疲劳应力、振动应力和冲击应力下铁路车辆座位的特性
简介：
信息：ICS：45.060.20 CCS：S04 发布：1995-12-01 实施：1995-12-20

简介： 信息：

ASTM E739-2010(2015) 线性或者线性化应力寿命 (S-N) 和应变寿命 (N) 疲劳数据的统计分析的标准实施规程
简介：4.1x00a0;Materials scientists and engineers are making increased use of statistical analyses in interpreting S-N and x03b5;-N fatigue data. Statistical analysis applies when the given data can be reasonably assumed to be a random sample of (or representation of) some specific defined population or universe of material of interest (under specific test conditions), and it is desired either to characterize the material or to predict the performance of future random samples of the material (under similar test conditions), or both. 1.1x00a0;This practice covers only S-N and x03b5;-N relationships that may be reasonably approximated by a straight line (on appropriate coordinates) for a specific interval of stress or strain. It presents elementary procedures that presently reflect good practice in modeling and analysis. However, because the actual S-N or x03b5;-N relationship is approximated by a straight line only within a specific interval of stress or strain, and because the actual fatigue life distribution is unknown, it is not recommended that (a) the S-N or x03b5;-N curve be extrapolated outside the interval of testing, or (b) the fatigue life at a specific stress or strain amplitude be estimated below approximately the fifth percentile (P x2243; 0.05). As alternative fatigue models and statistical analyses are continually being developed, later revisions of this practice may subsequently present analyses that permit more complete interpretation of S-N and x03b5;-N data.
信息：ICS：19.060 CCS： 发布：2010 实施：

KS B 6728-1995 压力容器的应力分析及疲劳分析
简介：이 규격은 KS B 6733의 3.에 규정하는 제1종 용기의 응력 해석 및 피로 해석에 대
信息：ICS： CCS：J74 发布：1995 实施：1995

简介： 信息：

ASTM E739-2010 线性或线性化应力寿命(S-N)和应变寿命(949;-N)疲劳数据统计分析的标准操作规程
简介：Materials scientists and engineers are making increased use of statistical analyses in interpreting S-N and x03B5;-N fatigue data. Statistical analysis applies when the given data can be reasonably assumed to be a random sample of (or representation of) some specific defined population or universe of material of interest (under specific test conditions), and it is desired either to characterize the material or to predict the performance of future random samples of the material (under similar test conditions), or both. 1.1 This practice covers only S-N and x03B5;-N relationships that may be reasonably approximated by a straight line (on appropriate coordinates) for a specific interval of stress or strain. It presents elementary procedures that presently reflect good practice in modeling and analysis. However, because the actual S-N or x03B5;-N relationship is approximated by a straight line only within a specific interval of stress or strain, and because the actual fatigue life distribution is unknown, it is not recommended that (a) the S-N or x03B5;-N curve be extrapolated outside the interval of testing, or (b) the fatigue life at a specific stress or strain amplitude be estimated below approximately the fifth percentile (P x2243; 0.05). As alternative fatigue models and statistical analyses are continually being developed, later revisions of this practice may subsequently present analyses that permit more complete interpretation of S-N and x03B5;-N data.
信息：ICS：19.060 CCS：H22 发布：2010 实施：

KS B 6728-1995 压力容器的应力分析及疲劳分析
简介：이 규격은 KS B 6733의 3.에 규정하는 제1종 용기의 응력 해석 및 피로 해석에 대
信息：ICS： CCS：J74 发布：1995 实施：1995

简介： 信息：

ISO/TR 1281-2 CORR 1-2009 滚动轴承.ISO 281的说明注释.第2部分:基于系统疲劳应力的改良额定寿命计算.技术勘误表1
简介：
信息：ICS：21.100.20 CCS：J11 发布：2009-10 实施：

NF P98-233-1-1994 路面试验.水硬性粘结剂材料疲劳性能测定.第1部分:恒定应力挠性疲劳试验
简介：
信息：ICS：93.080.20 CCS：P66 发布：1994-04-01 实施：1994-04-20

简介： 信息：

ISO/TR 1281-2 Technical Corrigendum 1-2009 滚动轴承.ISO 281的说明注释.第2部分:基于系统疲劳应力的改良额定寿命计算.技术勘误表1
简介：
信息：ICS：21.100.20 CCS：J11 发布：2009-10 实施：

CSN ISO 1352-1994 钢．扭应力疲劳测试
简介：Zpracovatel: Státní v?zkumn? ústav materiálu, Praha, I?O 002348 - Ing. Ivo ?ern? Technická normaliza?ní komise: TNK 64 Mechanické zkou?ení kov? Pracovník ?eského normaliza?ního institutu: Ing. Libu?e Sedláková
信息：ICS： CCS： 发布：1994 实施：

简介： 信息：

ISO/TR 1281-2-2008 滚动轴承.ISO 281的说明注释.第2部分:基于系统疲劳应力的改进额定寿命计算
简介：
信息：ICS：21.100.20 CCS：J11 发布：2008-12 实施：

JIS B8281-1993 压力容器的应力和疲劳分析
简介：
信息：ICS：23.020.30 CCS：J74 发布：1993-03-15 实施：

简介： 信息：

ISO/TR 1281-2:2008 滚动轴承——ISO 281第2部分:基于疲劳应力系统方法的改进额定寿命计算的说明
简介：
信息：ICS：21.100.20 CCS： 发布：2008-11-24 实施：

ASTM E739-1991(1998) 线性或线性化应力寿命(S-N)和应变寿命(e-N)疲劳数据的统计分析的标准规程
简介：1.1 This practice pertains only to S-N and e-N relationships that may be reasonably approximated by a straight line (on appropriate coordinates) for a specific interval of stress or strain. It presents elementary procedures that presently reflect good practice in modeling and analysis. However, because the actual S-N or e-N relationship is approximated by a straight line only within a specific interval of stress or strain, and because the actual fatigue life distribution is unknown, it is not recommended that (a) the S-N or e-N curve be extrapolated outside the interval of testing, or (b) the fatigue life at a specific stress or strain amplitude be estimated below approximately the fifth percentile (P [similar] 0.05). As alternative fatigue models and statistical analyses are continually being developed, later revisions of this practice may subsequently present analyses that permit more complete interpretation of S-N and e-N data.
信息：ICS：19.060 (Mechanical testing) CCS： 发布：1991 实施：

简介： 信息：

AGMA 08FTM14-2008 轴偏转和齿面修形对准双曲面齿轮应力分布和啮合疲劳寿命的影响
简介：
信息：ICS： CCS： 发布：2008 实施：

ASTM E739-1991(2004)e1 线性或线性化应力寿命(S-N)和应变寿命(<ε>-N)疲劳数据的统计分析用标准实施规程
简介：1.1 This practice covers only S-N and 949;-N relationships that may be reasonably approximated by a straight line (on appropriate coordinates) for a specific interval of stress or strain. It presents elementary procedures that presently reflect good practice in modeling and analysis. However, because the actual S-N or 949;-N relationship is approximated by a straight line only within a specific interval of stress or strain, and because the actual fatigue life distribution is unknown, it is not recommended that ( a) the S-N or 949;-N curve be extrapolated outside the interval of testing, or ( b) the fatigue life at a specific stress or strain amplitude be estimated below approximately the fifth percentile (P 0.05). As alternative fatigue models and statistical analyses are continually being developed, later revisions of this practice may subsequently present analyses that permit more complete interpretation of S-N and 949;-N data.
信息：ICS： CCS：H22 发布：1991 实施：

简介： 信息：

ASTM E2207-2008(2013)e1 带有薄壁管状样品的应力控制轴向扭曲疲劳检验的标准实施规程
简介：4.1x00a0;Multiaxial forces often tend to introduce deformation and damage mechanisms that are unique and quite different from those induced under a simple uniaxial loading condition. Since most engineering components are subjected to cyclic multiaxial forces it is necessary to characterize the deformation and fatigue behaviors of materials in this mode. Such a characterization enables reliable prediction of the fatigue lives of many engineering components. Axial-torsional loading is one of several possible types of multiaxial force systems and is essentially a biaxial type of loading. Thin-walled tubular specimens subjected to axial-torsional loading can be used to explore behavior of materials in two of the four quadrants in principal stress or strain spaces. Axial-torsional loading is more convenient than in-plane biaxial loading because the stress state in the thin-walled tubular specimens is constant over the entire test section and is well-known. This practice is useful for generating fatigue life and cyclic deformation data on homogeneous materials under axial, torsional, and combined in- and out-of-phase axial-torsional loading conditions. 1.1x00a0;The standard deals with strain-controlled, axial, torsional, and combined in- and out-of-phase axial torsional fatigue testing with thin-walled, circular cross-section, tubular specimens at isothermal, ambient and elevated temperatures. This standard is limited to symmetric, completely-reversed strains (zero mean strains) and axial and torsional waveforms with the same frequency in combined axial-torsional fatigue testing. This standard is also limited to characterization of homogeneous materials with thin-walled tubular specimens and does not cover testing of either large-scale components or structural elements. 1.2x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：19.060 (Mechanical testing) CCS： 发布：2008 实施：

CSN 72 2350-1983 机械应力疲劳试验方法
简介：Zpracovatel a oborové normaliza?ní st?edisko: Technick? a zku?ební ústav stavební, Praha - Ing. Vlastimil GrabmíillerPracovník ??adu pro normalizaci a mě?ení: Ing. Milena Veselá
信息：ICS： CCS： 发布：1983-4-25 实施：

简介： 信息：