非金属夹杂物检测标准

发布时间：2023-02-22 09:44:17

作者：北检院

阅读次数：

CNAS认证

CMA认证

ISO认证

AAA诚信企业

非金属夹杂物检测标准相关信息

ASTM B796-20 粉末锻造用铁粉非金属夹杂物含量的标准试验方法
简介：
信息：ICS：77.040.99 CCS：发布：2020-04-01 实施：

SIS MNC 1115-1988 非金属夹杂物评估Jernkontorets图表II
简介：This technical report is an introduction to the use of the Swedish standard SS 11 11 16. It also gives an example of the use of SS 11 11 16 for estimation of inclusions in pictures of optical images.
信息：ICS： CCS：发布：1988-09-15 实施：

BS EN 10247-2017 使用标准图片对钢的非金属夹杂物含量的显微图检验
简介：
信息：ICS：77.040.99 CCS：H11 发布：2017-09-19 实施：2017-09-30

JUS C.A3.014-1987 锻钢．非金属夹杂物含量宏观评定方法
简介：
信息：ICS： CCS：发布：1987-01-01 实施：

ISO 4967:2013 钢铁与粉煤灰；非金属夹杂物含量的测定——使用标准图的缩微摄影法
简介：
信息：ICS：77.040.99 CCS：发布：2013-07-24 实施：

CNS 2910-1986 钢内非金属夹杂物之显微镜试验方法
简介：本标准规定以显微镜测量钢内非金属夹杂物（以下简称夹杂物）之种类及数量，以决定钢内清净度之试验方法。
信息：ICS：77.040.99 CCS：发布：1986-03-17 实施：1986-03-17

KS D 0204-2007(2022) 钢－非金属夹杂物含量的测定－使用标准图的显微照相法
简介：
信息：ICS：77.040.99 CCS：发布：2007-11-26 实施：

ISO 4967:1979 钢.非金属夹杂物含量的测定.使用标准图表的显微照相法
简介：
信息：ICS：77.040.99 CCS：发布：1979-04-01 实施：

KS D 0204-2007(2017) 使用标准图的非金属夹杂物显微照相法的含量钢的测定
简介：
信息：ICS：77.040.99 CCS：发布：2007-11-26 实施：

ISO 4967-1979 钢.非金属夹杂物含量的测定.金相图与标准图比较法
简介：
信息：ICS：6020;1060 CCS：H24 发布：1979-04 实施：

NF A04-116-2007 使用标准图片对钢的非金属夹杂物含量的显微图检验
简介：
信息：ICS：77.040.99 CCS：H11 发布：2007-07-01 实施：2007-07-05

TS 3088-1978 锻钢　非金属夹杂物含量宏观评定方法
简介：
信息：ICS： CCS：发布：1978-01-01 实施：

DIN EN 10247-2007 使用标准图片对铁非金属夹杂物含量的显微图检验
简介：This European Standard defines a method of microscopic non-metallic inclusion assessment using picture charts.The method does not apply to particles of a length less than 3,0 μm or a width smaller than 2,0 μm. Defined by a product standard or agreement between the involved parties for certain special products, inclusions with a width below 2,0 μm can only be evaluated according to their length. Elongated inclusions with a lengthabove 1 410 μm are counted separately and are beyond the upper application limit of this standard. Globular inclusions with a diameter of 3,0 μm and above are included in the assessment.It is assumed, if particles are elongated or if there are stringers of particles, that they are parallel to each other. Other arrangements are not covered by this standard. This European Standard applies to samples with a microscopic precipitation approaching random distribution.From the data of measurements obtained by this method, evaluation according to other standards can be established.This European Standard does not apply to free cutting steels.NOTE The basic principle of this European Standard allows the determination of non-metallic inclusion content by image analysis techniques.
信息：ICS：77.040.99 CCS：H11 发布：2007-07 实施：

DS/ISO 3763-1977 锻钢.评定非金属夹杂物含量宏观检查.
简介：1 This International Standard describes the macroscopic methods used in current practice for assessing the content of non-metallic inclusions in wrought Steel products.2 Macroscopic methods are those dealing with non-metallic inclusions visible to the naked eye or with the aid of a magnifying glass with a magnification of not more than X 10. Only inclusions equal to or greater than 1 mm long are taken into consideration.3 The methods usually applied and defined in this International Standard are :- the blue fracture test method;- the step machined test method;- the magnetic particle inspection method.
信息：ICS：750 CCS：发布：1977 实施：

BS EN 10247-2007 使用标准图片对钢的非金属夹杂物含量的显微图检验
简介：This European Standard defines a method of microscopic non-metallic inclusion assessment using picturecharts.The method does not apply to particles of a length less than 3,0 µm or a width smaller than 2,0 µm. Definedby a product standard or agreement between the involved parties for certain special products, inclusions witha width below 2,0 µm can only be evaluated according to their length. Elongated inclusions with a lengthabove 1 410 µm are counted separately and are beyond the upper application limit of this standard. Globularinclusions with a diameter of 3,0 µm and above are included in the assessment.It is assumed, if particles are elongated or if there are stringers of particles, that they are parallel to eachother. Other arrangements are not covered by this standard. This European Standard applies to samples witha microscopic precipitation approaching random distribution.From the data of measurements obtained by this method, evaluation according to other standards can beestablished.This European Standard does not apply to free cutting steels.NOTE The basic principle of this European Standard allows the determination of non-metallic inclusion content byimage analysis techniques.
信息：ICS：77.040.99 CCS：H11 发布：2007-05-31 实施：2007-05-31

ISO 3763:1976 锻钢——评估非金属夹杂物含量的宏观方法
简介：
信息：ICS：77.040.99 CCS：发布：1976-08-01 实施：

EN 10247-2007 使用标准图片对铁非金属夹杂物含量的显微图检验
简介：This European Standard defines a method of microscopic non-metallic inclusion assessment using picture charts. The method does not apply to particles of a length less than 3,0 μm or a width smaller than 2,0 μm. Defined by a product standard or agreement between the involved parties for certain special products, inclusions with a width below 2,0 μm can only be evaluated according to their length. Elongated inclusions with a length above 1410 μm are counted separately and are beyond the upper application limit of this standard. Globular inclusions with a diameter of 3,0 μm and above are included in the assessment. It is assumed, if particles are elongated or if there are stringers of particles, that they are parallel to each other. Other arrangements are not covered byThis standard.This European Standard applies to samples with a microscopic precipitation approaching random distribution. From the data of measurements obtained byThis method, evaluation according to other standards can be established.This European Standard does not apply to free cutting steels. NOTE The basic principle of this European Standard allows the determination of non-metallic inclusion content by image analysis techniques.
信息：ICS： CCS：发布：2007-04-01 实施：

ISO 3763-1976 钢材评定非金属夹杂物含量的宏观方法
简介：Macroscopic methods deal with non-metallic inclusions visible to the naked eye or with the aid of a magnifying glass with a magnification of not more than X 10. Only inclusions equal to or greater than 1 mm long are taken into consideration. Covers the blue fracture test method, the step machined test method, the magnetic particle inspection method.
信息：ICS：77.040.99 CCS：H11 发布：1976-08 实施：

FORD SQ-M99P9001-A-2002 钢材中需通过显微检验才能发现的非金属夹杂物***与标准FORD WSS-M99P1111-A一起使用***
简介：
信息：ICS： CCS：发布：2002-08-19 实施：

UNI 6920-1971 航空用金属材料．钢材中的非金属夹杂物．分级和试验方法
简介：La presente norma riporta le prescrizioni di collaudo metallurgico dei blumi, billette, barre laminate a caldo o fucinate, tubi, fucinati o stampati di acciaio destinati alla fabbricazione dei particolari di uso aeronautico.
信息：ICS：49.025.10 CCS：V11 发布：1971-12-01 实施：1971-12-31

KS D ISO 3763-2002(2017) 锻钢宏观评估非金属夹杂物的含量的方法
简介：
信息：ICS：77.040.99 CCS：发布：2002-05-29 实施：

GOST 1778-1970 钢.非金属夹杂物的金相测定法
简介：Настоящий стандарт распространяется на стали и сплавы и устанавливает металлографические методы определения загрязненности их неметалл
信息：ICS：77.040.99 CCS：发布：1970 实施：1972-01-01

KS D ISO 3763-2002 锻钢.非金属夹杂物含量宏观评定方法
简介：이 규격은 가공용 강제품의 비금속 개재물 함량을 평가하기 위하여 현재 관례로 사용되고 있는
信息：ICS：77.040.99 CCS：H11 发布：2002-05-29 实施：2002-05-29

KS D 0204-2002 使用标准图的非金属夹杂物显微照相法的含量钢的测定
简介：
信息：ICS：77.040.99 CCS：发布：0000-00-00 实施：0000-00-00

KS D ISO 3763-2002(2022) 锻钢.评定非金属夹杂物含量的宏观方法
简介：
信息：ICS：77.040.99 CCS：发布：2002-05-29 实施：

FORD FLTM EU-BA 051-02-2001 弹簧中的非金属夹杂物
简介：
信息：ICS： CCS：发布：2001-03-02 实施：

FORD FLTM EU-BA 051-01-2000 硬化滚轴和滚珠轴承钢中的非金属夹杂物测定
简介：
信息：ICS： CCS：发布：2000-08-30 实施：

ISO 4967:1998 钢.非金属夹杂物含量的测定.使用标准图表的显微照相法
简介：
信息：ICS：77.040.99 CCS：发布：1998-10-08 实施：

ISO 4967-1998 钢非金属夹杂物含量的测定标准图显微法
简介：This International Standard specifies a micrographic method of determining the nonmetallic inclusions in rolled or forged steel products having a reduction ratio of at least 3 using standard diagrams. This method is widely used to assess the suitability of a steel for a given use. However, since it is difficult to achieve reproducible results owing to the influence of the test operator, even with a large number of specimens, precautions should be taken when using the method.NOTE For certain types of steel (e.g., free cutting steels), the standardized diagrams described in this International Standard may not be applicable.This International Standard also provides for the determination of nonmetallic inclusions by image analysis technologies (see annex D).
信息：ICS：77.040.99 CCS：H24 发布：1998-10 实施：

BS 7926-1998 铸钢非金属夹杂物百分比含量测定的定量显微照相法
简介：This British Standard specifies two micrographic methods for determining the non-metallic inclusion content of cast steels. Numerical values of the area fraction of non-metallic inclusions present in samples of cast steels is specified.The percentage content ranges of non-metallic inclusions are specified for four melting and refining methods in use in steel foundries throughout the UK.In addition to the definitive requirements, this standard also requires the items detailed in clause 4 to be documented. For compliance with this standard, both the definitive requirements and the documented items have to be satisfied.
信息：ICS：77.080.20 CCS：H25 发布：1998-08-15 实施：1998-08-15