密封性能检测标准

发布时间：2023-02-27 09:00:28

作者：北检院

阅读次数：

CNAS认证

CMA认证

ISO认证

AAA诚信企业

密封性能检测标准相关信息

GB/T 40325-2021 轨道车辆轮对滚动轴承橡胶密封装置性能试验
简介：
信息：ICS：83.140.50 CCS：G43 发布：2021-08-20 00:00:00.0 实施：2022-03-01 00:00:00.0

GB/T 4620-1984 缠绕式垫片水压密封性能试验方法
简介：
信息：ICS：23.040.80 CCS：Q61 发布：1984-07-30 实施：1985-06-01

ASTM C639-2015 弹性密封料流变 (流动) 性能的标准试验方法
简介： 5.1x00a0;The results obtained from this test method are simply a measure of the degree of horizontal or vertical flow of single-component or multi-component sealants when applied to a set joint configuration at two pre-determined temperatures. Only samples conditioned at the same temperature may be directly compared. 1.1x00a0;This test method describes a laboratory procedure for the determination of rheological (flow) properties of single- and multicomponent chemically curing sealants for use in building construction. 1.2x00a0;Other suitable flow characteristics may be agreed upon between the seller and purchaser or specifier. Special nonsag properties and lower flow characteristics may be required for use in sloping joints where absolute leveling is not desired. Note 1:x00a0;The sealants are supplied in various rheological properties ranging from pourable fluids to stiff nonsagging pastes. Multicomponent sealants are supplied as a base component with an activator or curing agent separately packaged. After mixing the multiple parts, the sealant is ready for application. Single-component sealants are supplied ready for use upon opening of the package and usually depend on the external environment for cure. 1.3x00a0;This test method describes four types of joint sealants: 1.3.1x00a0;Type Ix2014;Single-component flowable or self-leveling, 1.3.2x00a0;Type IIx2014;Single-component nonsag, 1.3.3x00a0;Type IIIx2014;Multicomponent flowable or self-leveling, and 1.3.4x00a0;Type IVx2014;Multicomponent nonsag. 1.4x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5x00a0;This standard does not purport to address the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.100.50 CCS：发布：2015 实施：

GB/T 39709-2020 动车组玻璃、车窗耐静压及车窗密封性能试验方法
简介：
信息：ICS：81.040.01 CCS：Q34 发布：2020-12-14 00:00:00.0 实施：2021-11-01 00:00:00.0

GB/T 32321-2015 滚动轴承密封深沟球轴承防尘、漏脂及温升性能试验规程
简介：
信息：ICS： CCS：发布：实施：2016-04-01

ASTM E2953-14 用于评估密封绝缘玻璃单元中电致变色器件加速老化性能的标准规范
简介：
信息：ICS：81.040.20 CCS：发布：2014-12-01 实施：

GB/T 39383-2020 埋地用无压热塑性塑料管道系统弹性密封圈接头的密封性能试验方法
简介：
信息：ICS：83.140.30 CCS：G33 发布：2020-11-19 00:00:00.0 实施：2021-06-01 00:00:00.0

IEC 63115-1-2020+AMD1-2022 CSV 含碱性或其他非酸性电解质的二次电池和电池组.工业用密封镍金属氢化物电池和电池.第1部分:性能
简介：
信息：ICS：29.220.30 CCS：发布：2022-11-07 实施：

KS M 2757-2014(2019) 测试方法用密封的含石棉建材的性能评价
简介：
信息：ICS：71.100.01 CCS：发布：2014-06-25 实施：

GB/T 38510-2020 涂覆式刺扎自密封轮胎自密封性能评价
简介：
信息：ICS：83.160.10 CCS：G41 发布：2020-03-06 00:00:00.0 实施：2021-02-01 00:00:00.0

IEC 63115-1-2020/AMD1-2022 修改件1.含碱性或其他非酸性电解质的二次电池和电池组.工业用密封镍金属氢化物电池和电池.第1部分:性能
简介：
信息：ICS：29.220.30 CCS：发布：2022-11-07 实施：

ASTM E2953-2014 评估密封绝缘玻璃装置中电致变色设备加速老化性能的标准试验方法
简介： 1.1x00a0;This specification is applicable to all electrochromic (EC) glass whose visible light transmittance or near infrared light transmittance properties, or both, can be changed reversibly by the application or removal of an electrical voltage. This includes absorptive and reflective EC devices. 1.2x00a0;This specification does not apply to other types of dynamic glass which do not solely require an electrical stimulus to change light transmittance such as photochromic and thermochromic glazings and hybrid active/passive chromogenics. 1.3x00a0;This specification covers electrochromic devices in preassembled permanently sealed insulting glass units with one or more cavities in which at least one lite contains an EC device (which may be in the form of a laminated lite or a single pane with coatings applied). This specification is also applicable to EC devices in preassembled insulating glass units with capillary tubes intentionally left open. As such this specification also requires conformance to Specification E2190. 1.4x00a0;This specification is applicable only to sealed insulating glass units that are constructed with glass and fabricated for vision glass areas for use in buildings, such as sliding doors, windows, skylights, and exterior wall systems. 1.5x00a0;Qualification under this specification is intended to provide a basis for evaluating the aging performance of electrochromic devices in sealed insulating glass units. 1.6x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS： CCS：发布：2014 实施：

GB/T 38510-2020 涂覆式刺扎自密封轮胎自密封性能评价
简介：
信息：ICS：83.160.10 CCS：G41 发布：2020-03-06 00:00:00.0 实施：2021-02-01 00:00:00.0

IEC 61753-111-09-2021 纤维光学互连器件和无源元件.性能标准.第111-09部分:密封密封件.S类.地下
简介：
信息：ICS：33.180.20 CCS：发布：2021-09-14 实施：

JIS B2402-4-2013 组合弹性密封元件的旋转轴唇型密封件.第4部分:性能试验规程
简介：
信息：ICS：23.100.60;83.140.50 CCS：G43 发布：2013-06-20 实施：

GB/T 38510-2020 涂覆式刺扎自密封轮胎自密封性能评价
简介：
信息：ICS：83.160.10 CCS：G41 发布：2020-03-06 00:00:00.0 实施：2021-02-01 00:00:00.0

IEC 61753-111-09:2021 纤维光学互连器件和无源元件.性能标准.第111-09部分:密封密封件.S类.地下
简介：
信息：ICS：33.180.20 CCS：发布：2021-09-14 实施：

JIS B2402-4-2013 组合弹性密封元件的旋转轴唇型密封件.第4部分:性能试验规程
简介：
信息：ICS：23.100.60;83.140.50 CCS：G43 发布：2013-06-20 实施：

GB/T 36110-2018 文物展柜密封性能及检测
简介：
信息：ICS：21.020 CCS：J01 发布：2018-03-15 00:00:00.0 实施：2018-10-01 00:00:00.0

IEC 61753-111-07:2021 纤维光学互连器件和无源元件.性能标准.第111-07部分:密封外壳.A类.天线
简介：
信息：ICS：33.180.20 CCS：发布：2021-09-03 实施：

SAE J1610-2012 PVT试验性能的软管连接密封性能评价的试验方法
简介：This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This test method provides a standardized procedure for evaluating the sealing capability of a hose connection or any of the individual components of the connection with a pressure, vibration, and temperature (PVT) test facility. This test method consists of a test procedure which includes vibration and coolant flow and a similar test procedure specified without vibration or coolant flow. Any test parameters, other than those
信息：ICS：21.140;43.040.01 CCS：T32 发布：2012-10-24 实施：

GB/T 36110-2018 文物展柜密封性能及检测
简介：本标准规定了文物展柜的密封程度分类、密封性能要求、密封通用要求、展柜换气率检测方法。本标准适用于各种具有密封要求的文物展柜，也适用于具有密封要求的文物储藏柜。
信息：ICS：21.020 CCS：J01 发布：2018-03-15 实施：2018-10-01

IEC 61753-111-08:2021 光纤互连设备和被动元件性能标准 - 第111-8部分:G类接地密封
简介：
信息：ICS：33.180.20 CCS：发布：2021-04-07 实施：

DIN EN 1109-2012 防水软板.屋顶密封沥青板.冷弯性能测定.德文版本FprEN 1109-2012
简介：
信息：ICS：91.100.50 CCS：Q17 发布：2012-10-01 实施：

GB/T 34032-2017 船舶与海上技术管路系统衬垫密封机械接头及其附件性能规范
简介：
信息：ICS：47.020.30 CCS：U55 发布：2017-07-31 00:00:00.0 实施：2018-02-01 00:00:00.0

IEC 61753-111-08-2021 纤维光学互连器件和无源元件. 性能标准. 第111-8部分: 地面类G密封闭包
简介：This part of IEC 61753 contains the minimum tests, test severities and measurement requirements which a sealed fibre optic closure need to meet in order to be categorised as meeting the IEC standard for category G - Ground, as defined in Table A.14 of IEC 61753-1:2018. Free breat
信息：ICS：33.180.20 CCS：L23 发布：2021-04-01 实施：

NF E48-372-4-2012 密封元件为弹性体材料的旋转轴唇形密封圈 - 第4部分: 性能试验程序.
简介：
信息：ICS：23.100.60 CCS：J22 发布：2012-09-01 实施：2012-09-22

GB/T 21283.6-2015 密封元件为热塑性材料的旋转轴唇形密封圈第6部分:热塑性材料与弹性体包覆材料的性能要求
简介：GB/T 21283的本部分规定了密封元件为热塑性材料的旋转轴唇形密封圈（以下简称密封圈）用热塑性材料聚四氟乙烯（简称PTFE）与弹性体包覆橡胶材料的分类、要求、检验规则及包装和贮存。本部分适用于密封元件是以热塑性材料聚四氟乙烯为基材制成的旋转轴唇形密封圈。
信息：ICS：23.100.60 CCS：J20 发布：2015-12-31 实施：2016-07-01

DIN EN IEC 63115-1-2021 含有碱性或其他非酸性电解质的二次电池和电池. 工业应用的密封镍金属氢化物电池和电池. 第1部分: 性能(IEC 63115-1-2020); 德文版本EN IEC 63115-1-2020
简介：This International Standard specifies marking, designation, tests and requirements for the sealed nickel-metal hydride cells and batteries used in industrial applications including stationary applications. Examples of applications for this standard are stationary applications lik
信息：ICS：29.220.30 CCS：K82 发布：2021-01-00 实施：2021-01-01

SAE J1453-1-2012 O型圈面密封连接器规格:第1部分:管连接详情及性能和试验通用要求
简介：The three parts of SAE J 1453 cover material, dimensional, and performance requirements of steel O-ring face seal (ORFS) connectors for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for normal tube diameters of 6 mm through 50 mm. These connectors are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These connectors are capable of providing leak proof full flow connections in hydraulic systems operating from 95 kPa vacuum to the working pressures shown in Tables 1 and 2. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums. For any application, it is recommended that sufficient testing be conducted and reviewed by both the user and manufacturer to ensure that required performance levels are met. For use of these connectors in conditions outside the pressure and temperature limits specified, the manufacturers must be consulted. Both metric and inch tubing can be accommodated by changing only the sleeve to match the tube diameters. In the past, these connectors have been used predominantly with inch tubing. For new designs, the use of metric tubing should be considered.
信息：ICS：23.040.80 CCS：T33 发布：2012-05-03 实施：

PNS ASTM C1315-2021 养护和密封混凝土用具有特殊性能的液膜形成化合物的标准规范
简介：
信息：ICS：91.100.50 CCS：Q92 发布：2021 实施：

SAE J1453-1-2012 O形面密封连接器的规格: 第1部分. 管路连接详情和通用性能和试验要求
简介：The three parts of SAE J1453 cover material, dimensional, and performance requirements of steel O-ring face seal(ORFS) connectors for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tubediameters of 6 mm through 50 mm.
信息：ICS： CCS：发布：2012-05 实施：2012-05

GB/T 32217-2015 液压传动密封装置评定液压往复运动密封件性能的试验方法
简介：本标准规定了评定液压往复运动密封件性能的试验条件和方法。本标准适用于以液压油液为传动介质的液压往复运动密封件性能的评定。
信息：ICS：23.100.99;83.140.50 CCS：J20 发布：2015-12-10 实施：2017-01-01

ASTM E2953-14(2020)e1 用于评估密封绝缘玻璃单元中电致变色器件加速老化性能的标准规范
简介：
信息：ICS：81.040.20 CCS：发布：2020-07-01 实施：

FORD WSB-M18P11-A2-2012 低温扩张密封层的性能要求***与福特WSS-M99P1111-A***一起使用[使用:福特WSS-M18P11-B3]
简介：
信息：ICS： CCS：发布：2012-04-04 实施：

GB/T 21283.4-2008 密封元件为热塑性材料的旋转轴唇形密封圈.第4部分:性能试验程序
简介：警告——使用本部分的人员宣熟悉常用的实验室操作规程。本部分的意图并不是涉及到所有的安全问题，如果有的话，也与其使用有关，在操作热和冷的液体和装置时，需注意采用合理的预防措施。使用者有责任建立适当的安全和健康惯例，并确保符合国家法规的要求。GB/T 21283的本部分描述了密封元件为热塑性材料的旋转轴唇形密封圈，密封元件是以热塑性材料如聚四氟乙烯(PTFE)为基,经适当配合制成的。本部分规定了可用于对密封元件为热塑性材料的旋转轴唇形密封圈进行合格鉴定的通用性能试验。还规定了动态试验和辅助低温试验和材料的要求。本部分适用于密封元件为热塑性材料的旋转轴唇形密封圈（以下简称密封圈）。
信息：ICS：83.140.50;23.100.60 CCS：G43 发布：2008-05-14 实施：2008-10-01

T/CSAE 137-2020 汽车紧固点防水密封性能试验及评价方法
简介：本标准规定了防水密封性能等级、试验方法、实验结果评价及特殊要求。本标准适用于汽车紧固点的一般防水密封性能测试和评价。本标准不适用于气密性测试。
信息：ICS：43.020 CCS：C3650 发布：2020-05-29 实施：2020-06-05

FORD WSS-M18P11-B3-2012 密封层,预成型部件的涂料车间固化性能要求***与福特WSS-M99P1111-A***一起使用
简介：
信息：ICS： CCS：发布：2012-04-04 实施：

GB/T 12385-2008 管法兰用垫片密封性能试验方法
简介：
信息：ICS： CCS：J13 发布：2008-05-07 实施：2008-11-01

IEC 63115-1:2020 含碱性或其他非酸性电解质的二次电池和电池.工业用密封金属氢化物镍电池和电池.第1部分:性能
简介：
信息：ICS：29.220.30 CCS：发布：2020-01-20 实施：

BS ISO 16589-4-2011 含热塑性密封元件的旋转轴唇型密封件.性能试验程序
简介：
信息：ICS：21.140;83.140.50 CCS：G43 发布：2012-03-31 实施：2012-03-31

GB/T 13871.4-2007 密封元件为弹性体材料的旋转轴唇形密封圈第4部分:性能试验程序
简介：GB／T l3871的本部分规定了密封元件为弹性体材料的旋转轴唇形密封圈的试验要求和方法。本部分适用于合格鉴定试验，也适用于材料控制试验、动态试验和附加的低温试验等。
信息：ICS：83.140.50;23.100.60 CCS：G43 发布：2007-12-13 实施：2008-07-01

IEC 63115-1-2020 含碱性或其他非酸性电解质的二次电池和电池.工业用密封金属氢化物镍电池和电池.第1部分:性能
简介：
信息：ICS：29.220.30 CCS：发布：2020-01-20 实施：

GMW GMW3041-2011 固定汽车玻璃的粘合和密封性能要求.第4次出版(英文版本)
简介：
信息：ICS： CCS：发布：2011-09-01 实施：

GB/T 15520-1995 石棉橡胶板蒸汽密封性能试验方法
简介： 本标准规定了石棉橡胶板高温高压水蒸气密封性能的试验方法。本标准适用于XB450、XB350和XB200三种牌号石棉橡胶板的蒸汽密封性能试验。其他牌号的石棉橡胶板亦应参照本标准进行蒸汽密封性能试验。
信息：ICS：73.080 CCS：Q61 发布：1995-04-04 实施：1995-12-01

ASTM C1315-19 养护和密封混凝土用具有特殊性能的液膜形成化合物的标准规范
简介：
信息：ICS：91.100.50 CCS：发布：2019-06-15 实施：

SAE J1453-1-2011 O型环面密封连接器规范(R):第1部分.性能和试验中管道连接的详细信息和通用要求
简介：1.1 PurposeThe three parts of SAE J1453 cover material, dimensional, and performance requirements of steel O-ring face seal(ORFS) connectors for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tubediameters of 6 mm through 50 mm.1.2 Field of ApplicationThese connectors are intended for general application and hydraulic systems on industrial equipment and commercialproducts, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. Theseconnectors are capable of providing leak proof full flow connections in hydraulic systems operating from 95 kPa vacuumto the working pressures shown in Tables 1 and 2. Since many factors influence the pressure at which a hydraulicsystem will or will not perform satisfactorily, these values should not be construed as guaranteed minimums. For anyapplication, it is recommended that sufficient testing be conducted and reviewed by both the user and manufacturer toensure that required performance levels are met.For use of these connectors in conditions outside the pressure and temperature limits specified, the manufacturers mustbe consulted.Both metric and inch tubing can be accommodated by changing only the sleeve to match the tube diameters. In the past,these connectors have been used predominantly with inch tubing. For new designs, the use of metric tubing should beconsidered.
信息：ICS： CCS：T33 发布：2011-08-01 实施：

GB/T 15171-1994 软包装件密封性能试验方法
简介： 本标准规定了软包装件密封性能的试验方法。本标准适用于各种材料制成的密封软包装件试验。
信息：ICS：55.020 CCS：A83 发布：1994-08-16 实施：1995-03-01

BS PD CEN/TS 16969-2016 涂料和清漆. 外部木材的涂层材料和涂层系统. 端面纹理密封性能评定
简介：
信息：ICS：87.040 CCS：发布：2016-08-31 实施：2016-08-31

ASTM C1315-11 养护和密封混凝土用具有特殊性能的液膜形成化合物的标准规范
简介：
信息：ICS：91.100.50 CCS：发布：2011-06-01 实施：

GB/T 13878-1992 农业轮式拖拉机和自走机具密封驾驶室采暖和通风系统性能试验方法
简介： 本标准规定了封闭驾驶室采暖和通风系统的性能试验方法。本标准适用于农业拖拉机和自走式机具的封闭驾驶室采暖和通风系统。采暖系统可以是靠发动机供热的，也可以是不靠发动机供热的。如是后者，应根据制造厂说明书操纵采暖系统。根据本试验方法，在规定的温度和空气流速下，可测定驾驶室内的气候，据此可以比较不同类型驾驶室采暖和通风系统的性能。
信息：ICS：65.060.10 CCS：T69 发布：1992-11-14 实施：1993-07-15

ISO 16589-4-2011 带热塑密封件的旋转轴唇型密封.第4部分:性能试验程序
简介：WARNING — Persons using this part of ISO 16589 should be familiar with normal laboratory practice.Whilst this part of ISO 16589 does not purport to address all the safety problems, if any, associatedwith its application, attention is drawn to the need to employ sensible precautions while handling hotand cold fluids and equipment. It is the responsibility of the user of this part of ISO 16589 to establishappropriate safety and health practices and to ensure compliance with any national regulatoryconditions.ISO 16589 specifies seals utilizing sealing elements manufactured from suitably formulated compounds basedon thermoplastic materials, such as polytetrafluoroethylene (PTFE). They are considered suitable for useunder low pressure conditions.This part of ISO 16589 specifies general performance tests which can be used for seal qualification purposes.Materials quality control, dynamic testing, and supplementary low temperature testing requirements arecovered.NOTE ISO 16589 is complementary to ISO 6194, which covers seals incorporating elastomeric sealing elements.
信息：ICS：23.100.60;83.140.50 CCS：J22 发布：2011-04-15 实施：

GB/T 12385-1990 管法兰用垫片密封性能试验方法
简介： 本标准规定了管道法兰用垫片密封性能的A、B两种试验方法。本标准的两种试验方法均适用于石棉橡胶垫片、聚四氟乙烯包复垫片、金属包复垫片、缠绕式垫片及金属垫片。
信息：ICS：23.040.80 CCS：J15 发布：1990-06-23 实施：1991-07-01

PD CEN/TS 16969-2016 涂料和清漆-涂层材料和涂层系统外部木材-对端粒密封性能的评定
简介：This Technical Specification specifies a test method to evaluate the ability of coating materials to seal the end grain of wood against ingress of water. This procedure is relevant for joinery or wood based cladding materials whose service life can depend on the control of water penetration through the coated end-grain.
信息：ICS：87.040 CCS：Q18 发布：2016-07 实施：

ASTM C1315-2011 固化混凝土和密封混凝土用液膜成型化合物特种性能的标准规范
简介：1.1 This specification provides requirements for membrane-forming liquids suitable for use as curing compounds and sealers on freshly placed concrete and as sealers on hardened concrete. These membranes have special properties, such as, alkali resistance, acid resistance, adhesion-promoting qualities, and resistance to degradation by UV light. Note 18212;For liquid membrane-forming curing compounds specified primarily by their ability to retain water in newly placed concrete (and by drying time, and for white pigmented products, reflectance), see Specification C309. 1.2 The values stated in SI units are to be regarded as the standard. (Inch pound units are shown in parentheses). 1.3 The following precautionary caveat pertains only to the test methods portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This is a performance specification. The allowable composition of products covered by this specification is limited by various local, regional, and national regulations. Issues related to air quality (solvent emission), worker exposure, and other hazards are not addressed here. It is the responsibility of the producers and users of these materials to comply with pertinent regulations.WarningSome VOC exempt solvents used to meet the regulations are extremely flammable with low auto ignition temperatures and rapid evaporation rates. Consult the manufacturer''s product information sheet for important application and safety information.
信息：ICS：91.100.50 (Binders. Sealing materials) CCS：Q13 发布：2011 实施：

GB/T 4621-1984 缠绕式垫片蒸汽密封性能试验方法
简介：
信息：ICS：23.040.80 CCS：Q61 发布：1984-07-30 实施：1985-06-01

BS EN 16508-2015 临时工程设备. 密封结构. 性能要求和通用设计
简介：
信息：ICS：91.120.01;91.200 CCS：P36 发布：2015-12-31 实施：2015-12-31

ASTM D7349/D7349M-2011 测定屋顶防水材料密封紧固件密封性能的标准试验方法
简介：In some situations, penetration through asphalt-based roofing or waterproofing materials by fasteners is a required part of the material installation process or occurs during installation of other system components. When fasteners penetrate the material as a purposeful and planned part of the construction process, it is reasonable to expect that materials designed to limit migration of liquid water at the interface between the penetrating fastener and the material will do so. This qualitative test method provides a means to evaluate the ability of a material to limit water migration at fastener penetrations when tested under defined conditions.1.1 This qualitative test method determines the capability of asphalt-based roofing or waterproofing material to seal around a fastener that penetrates the material and prevent transmission of liquid water through the material at the penetration under defined conditions. 1.2 This test method is provided for adoption by ASTM or other consensus-based roofing and waterproofing product specifications as a standardized means to evaluate capability to seal around a fastener. Performance of this test method after subjecting the product to conditioning intended to simulate environmental stresses and strains is not prohibited. 1.3 The text of this test method references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：91.100.50 CCS：Q17 发布：2011 实施：