防锈性能检测标准

发布时间：2023-02-23 07:06:23

作者：北检院

阅读次数：

CNAS认证

CMA认证

ISO认证

AAA诚信企业

防锈性能检测标准相关信息

GB/T 26105-2010 防锈油防锈性能试验多电极电化学法
简介：本标准规定了评定防锈油防锈性能试验的多电极电化学法测试方法、设备和步骤。本标准适用于铁基材料上防锈油防锈性能的比较试验。
信息：ICS：25.220-70 CCS：A29 发布：2011-01-10 实施：2011-10-01

KS M 2009-2007(2017) 润滑油防锈性能试验方法
简介：
信息：ICS：75.080 CCS：发布：2007-06-29 实施：

GB/T 26109-2010 水基防锈液防锈性能试验多电极电化学法
简介：本标准规定了评价水基防锈液防锈性能试验的多电极电化学测试方法、设备和程序。本标准适用于铁基材料上水基防锈液防锈性能的比较试验。
信息：ICS：25.220-70 CCS：A29 发布：2011-01-10 实施：2011-10-01

JB/T 10527-2005 水基防锈液防锈性能试验.多电极电化学法
简介： 本标准规定了评价水基防锈液防锈性能试验的多电极电化学测试方法、设备和程序。本标准适用于水基防锈液对铁基材料防锈性能的比较试验。
信息：ICS：25.220.70 CCS：A29 发布：2005-09-23 实施：2006-02-01

GB/T 11143-2008 加抑制剂矿物油在水存在下防锈性能试验法
简介： 本标准规定了加抑制剂矿物油在水存在下防锈性能的测定方法。本标准适用于评价加抑制剂矿物油，特别是汽轮机油在与水混合时对铁部件的防锈能力，还适用于液压油、循环油等其他油品及比水密度大的液体。本标准涉及到某些有危险性的材料、操作及设备，但并未对所有的安全问题提出建议。因此，用户在使用本标准前应建立适当的安全防范措施，并制定相应的管理制度。
信息：ICS：75.100 CCS：E38 发布：2008-02-13 实施：2008-09-01

JB/T 10528-2005 防锈油防锈性能试验.多电极电化学法
简介： 本标准规定了评价防锈油防锈性能试验的多电极电化学测试方法、设备和程序。本标准适用于铁基材料上防锈油防锈性能的比较试验。
信息：ICS：25.220.70 CCS：A29 发布：2005-09-23 实施：2006-02-01

GB/T 19230.1-2003 评价汽油清净剂使用效果的试验方法第1部分;汽油清净剂防锈性能试验方法
简介：本部分规定了汽油清净剂防锈性能的试验方法与试验设备。本部分适用于汽油洁净剂的防锈性能的评价。
信息：ICS：75.140 CCS：E49 发布：2003-07-01 实施：2003-12-01

ASTM D6557-2004 汽车发动机油防锈性能评定的标准试验方法
简介：This bench test method was designed as a replacement for Test Method D 5844. Test Method D 5844 was designed to measure the ability of an engine oil to protect valve train components against rusting or corrosion under low temperature, short-trip service, and was correlated with vehicles in that type of service prior to 1978.5 5.1.1 Correlation between these two test methods has been demonstrated for most, but not all, of the test oils evaluated.1.1 This test method covers a Ball Rust Test (BRT) procedure for evaluating the anti-rust ability of fluid lubricants. The procedure is particularly suitable for the evaluation of automotive engine oils under low-temperature, acidic service conditions.1.2 Information Letters are published occasionally by the ASTM Test Monitoring Center (TMC) to update this test method. Copies of these letters can be obtained by writing the center.1.3 The values stated in either SI units or in other units shall be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, use each system independently of the other, without combining values in any way.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 7.1.1-7.1.3 and 8.2.1.1.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E34 发布：2004 实施：

GB/T 11143-1989 加抑制剂矿物油在水存在下防锈性能试验法
简介： 本标准规定了加抑制剂矿物油在水存在下防锈性能的测定方法。本标准适用于评定加抑制剂的矿物油，特别是汽轮机油在同水混合时对铁部件的防锈能力。本标准也适用于其他油品，例如液压油、循环油以及比水重的液体。
信息：ICS：75.100 CCS：E30 发布：1989-03-31 实施：1990-04-07

KS M ISO 11007-2003 石油产品和润滑剂.润滑脂防锈性能的测定
简介：이 규격은 수용성 시험 유체가 존재할 때, 윤활 그리스의 방청 성능을 시험하는 시험 방법에
信息：ICS：75.100 CCS：E34 发布：2003-03-04 实施：2003-03-04

GB 11143-1989 加抑制剂矿物油在水存在下防锈性能试验法
简介：
信息：ICS： CCS：E38 发布：1989-03-31 实施：1990-04-01

NF T60-135-1-2021 石油产品和润滑剂. 润滑脂防锈性能的测定. 第1部分: 动态潮湿条件
简介：
信息：ICS：75.100 CCS：E34 发布：2021-09-25 实施：2021-09-25

ASTM D6557-2003 汽车发动机油防锈性能评价的标准试验方法
简介：1.1 This test method covers a Ball Rust Test (BRT) procedure for evaluating the antirust ability of fluid lubricants. The procedure is particularly suitable for the evaluation of automotive engine oils under low-temperature, acidic service conditions.1.2 Information Letters are published occasionally by the ASTM Test Monitoring Center (TMC) to update this test method. Copies of these letters can be obtained by writing the center.1.3 The values stated in either SI units or in other units shall be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, use each system independently of the other, without combining values in any way.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 7.1.1-7.1.3, 8.2.1.1, and Table 1.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E34 发布：2003 实施：

ISO/TS 11007-2-2021 石油产品和润滑剂. 润滑脂防锈性能的测定. 第2部分: 水洗法
简介：
信息：ICS：75.100 CCS：E34 发布：2021-07-00 实施：

DIN ISO 7120-2000 石油产品和润滑剂.石油润滑油和其他液体.在含水情况下防锈性能的测定
简介：The document specifies a method for evaluating peroleum oils and other fluids to indicate their effectiveness in preventing the rusting of ferrous parts should water becomes mixed with the oil/fluid. The methodis is for application to inhibited mineral oils including steam turbine oils, circulating oils and hydraulic oils and non-hydrocarbon fluids including fluids denser than water.,,
信息：ICS：75.080 CCS：E34 发布：2000-05 实施：

ISO 11007-1-2021 石油产品和润滑剂. 润滑脂防锈性能的测定. 第1部分: 动态潮湿条件
简介：
信息：ICS：75.100 CCS：E34 发布：2021-07-00 实施：

ASTM D6557-2000 汽车发动机油防锈性能评定的标准试验方法
简介：1.1 This test method covers a Ball Rust Test (BRT) procedure for evaluating the antirust ability of fluid lubricants. The procedure is particularly suitable for the evaluation of automotive engine oils under low-temperature, acidic service conditions.1.2 Information Letters are published occasionally by the ASTM Test Monitoring Center (TMC) to update this test method. Copies of these letters can be obtained by writing the center.1.3 The values stated in either SI units or in other units shall be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, use each system independently of the other, without combining values in any way.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See7.1.1, 7.1.2, 7.1.3, 8.2.1.1 and Table 1.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E34 发布：2000 实施：

KS M ISO 17463-2018 油漆和清漆 - 通过加速循环电化学技术测定有机涂层的防锈性能指南
简介：
信息：ICS：87.040 CCS：发布：2018-03-22 实施：

JC/T 855-1999 蒸压加气混凝土板钢筋涂层防锈性能试验方法
简介：
信息：ICS：91.100 CCS：Q10 发布：1999-06-15 实施：2000-01-01

GOST ISO 7120-2015 石油制品和润滑剂. 石油和其它液体. 在存在水的条件下防锈性能的测定
简介：
信息：ICS：75.080 CCS：E36 发布：2015 实施：2017-01-01

SH/T 0650-1997 金属保护剂防锈性能试验法( 潮湿箱法)
简介：
信息：ICS： CCS：E41 发布：1997-10-27 实施：1998-07-01

GOST ISO 7120-2015 石油制品和润滑剂. 石油和其它液体. 在存在水的条件下防锈性能的测定
简介：
信息：ICS：75.080 CCS：发布：2015 实施：2017-01-01

ISO 11007-1997 石油产品和润滑剂润滑脂防锈性能的测定
简介：This International Standard specifies a method for the determination of the rust-prevention characteristics of lubricating grease in the presence of an aqueous test fluid.
信息：ICS：75.100 CCS：E34 发布：1997-06 实施：

ISO 17463:2014 油漆和清漆 - 通过加速循环电化学技术测定有机涂层的防锈性能指南
简介：
信息：ICS：87.040 CCS：发布：2014-07-21 实施：

NF T60-173-1994 临时防蚀产品.防锈性能的测定.湿度室法
简介：
信息：ICS：75.100 CCS：A29 发布：1994-12-01 实施：1994-12-20

NB/SH/T 0517-2014 车辆齿轮油防锈性能的评定 L-33-1法
简介：本标准规定了采用准双曲面齿轮驱动桥在有水存在和加温条件下,测定车辆齿轮油的抗锈蚀性能的试验方法。本试验标准通常称为L-33-1试验。本标准适用于测定车辆齿轮油的抗锈蚀性。
信息：ICS：75.100 CCS：E34 发布：2014-06-29 实施：2014-11-01

ASTM D5534-1994(2005) 液压液体汽相防锈性能的标准试验方法
简介：Procedures such as Test Methods D 665 and D 3603 assess the ability of new or unused hydraulic fluid to prevent rusting on wetted steel surfaces but do not address the prevention of rusting in the vapor space above the fluid. This procedure addresses the latter question under one set of test conditions and need not be applicable to some service conditions. Since used fluids have not been cooperatively tested in this procedure, its utility for in-service monitoring has not been established.1.1 This test method covers the ability of hydraulic fluids to prevent the rusting of steel in the vapor phase over the hydraulic fluid and water.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.120 (Hydraulic fluids) CCS：E39 发布：1994 实施：

NF T60-186-1993 含水金属加工液.接触黑色金属的防锈性能测定
简介：
信息：ICS：75.100 CCS：E30 发布：1993-12-01 实施：1993-12-20

ASTM D665-2014 加抑制剂矿物油在水存在下防锈性能的标准试验方法
简介： 5.1x00a0;In many instances, such as in the gears of a steam turbine, water can become mixed with the lubricant, and rusting of ferrous parts can occur. This test indicates how well inhibited mineral oils aid in preventing this type of rusting. This test method is also used for testing hydraulic and circulating oils, including heavier-than-water fluids. It is used for specification of new oils and monitoring of in-service oils. Note 3:x00a0;This test method was used as a basis for Test Method D3603. Test Method D3603 is used to test the oil on separate horizontal and vertical test rod surfaces, and can provide a more discriminating evaluation. 1.1x00a0;This test method covers the evaluation of the ability of inhibited mineral oils, particularly steam-turbine oils, to aid in preventing the rusting of ferrous parts should water become mixed with the oil. This test method is also used for testing other oils, such as hydraulic oils and circulating oils. Provision is made in the procedure for testing heavier-than-water fluids. Note 1:x00a0;For synthetic fluids, such as phosphate ester types, the plastic holder and beaker cover should be made of chemically resistant material suitable for the type of fluid tested. 1.2x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 7.4 x2013; 7.6.
信息：ICS：75.080 CCS：发布：2014 实施：

JIS K2510-1987 润滑油防锈性能试验方法
简介：
信息：ICS：75.100 CCS：E30 发布：1987-10-01 实施：1987-10-01

GOST ISO 11007-2013 石油制品和润滑剂. 润滑脂防锈性能的测定
简介：
信息：ICS：75.100 CCS：发布：2013 实施：2015-01-01

ISO 7120-1987 石油产品和润滑剂石油原油和其他液体水存在时防锈性能的测定
简介：Defines a method for evaluating these products to indicate the effectiveness in preventing the rusting of ferrous parts should water becomes mixed the oil/fluid. The methodis for application to inhibited oils including steam turbine oils, circulating oils and hydraulic oils and non-hydrocarbon fluids including fluids denser than water.
信息：ICS：75.080 CCS：E34 发布：1987-04 实施：

ASTM D6557-2013 评定汽车发动机油防锈性能的标准试验方法
简介： 5.1x00a0;This bench test method was designed as a replacement for Test Method D5844. Test Method D5844 was designed to measure the ability of an engine oil to protect valve train components against rusting or corrosion under low temperature, short-trip service, and was correlated with vehicles in that type of service prior to 1978.5 5.1.1x00a0;Correlation between these two test methods has been demonstrated for most, but not all, of the test oils evaluated. 1.1x00a0;This test method covers a Ball Rust Test (BRT) procedure for evaluating the anti-rust ability of fluid lubricants. The procedure is particularly suitable for the evaluation of automotive engine oils under low-temperature, acidic service conditions. 1.2x00a0;Information Letters are published occasionally by the ASTM Test Monitoring Center (TMC)2 to update this test method. Copies of these letters can be obtained by writing the center. 1.3x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3.1x00a0;Exceptionsx2014;Where there is no direct equivalent, such as the units for screw threads, national pipe threads/diameters, and tubing size. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 7.1.1-7.1.3 and 8.2.1.1.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E34 发布：2013 实施：

CNS 10452-1983 防锈油防锈性能检验法
简介：本标准规定防锈油之防锈性能检验法。
信息：ICS：71.100.01;71.040.40 CCS：发布：1983-07-11 实施：1983-07-11

ASTM D6557-2010a 评估汽车发动机润滑油的防锈性能的标准试验方法
简介：This bench test method was designed as a replacement for Test Method D5844. Test Method D5844 was designed to measure the ability of an engine oil to protect valve train components against rusting or corrosion under low temperature, short-trip service, and was correlated with vehicles in that type of service prior to 1978. Correlation between these two test methods has been demonstrated for most, but not all, of the test oils evaluated.1.1 This test method covers a Ball Rust Test (BRT) procedure for evaluating the anti-rust ability of fluid lubricants. The procedure is particularly suitable for the evaluation of automotive engine oils under low-temperature, acidic service conditions. 1.2 Information Letters are published occasionally by the ASTM Test Monitoring Center (TMC) to update this test method. Copies of these letters can be obtained by writing the center. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3.1 Exceptions8212;Where there is no direct equivalent, such as the units for screw threads, national pipe threads/diameters, and tubing size. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 7.1.1-7.1.3 and 8.2.1.1.
信息：ICS：75.100 CCS：E34 发布：2010 实施：

GOST 19199-1973 润滑油.防锈性能测定法
简介：Настоящий стандарт распространяется на турбинные, гидравлические и другие смазочные масла, для которых возможен контакт с водой в услови
信息：ICS：75.100 CCS：发布：1973 实施：1975-01-01

KS M 2009-2007(2022) 润滑油防锈性能试验方法
简介：
信息：ICS：75.080 CCS：发布：2007-06-29 实施：