滴点检测标准

发布时间：2023-02-23 10:40:28

作者：北检院

阅读次数：

CNAS认证

CMA认证

ISO认证

AAA诚信企业

滴点检测标准相关信息

GB/T 2951.51-2008 电缆和光缆绝缘和护套材料通用试验方法.第51部分:填充膏专用试验方法.滴点.油分离.低温脆性.总酸值.腐蚀性.23℃时的介电常数.23℃和100℃时的直流电阻率
简介：GB/T 2951的本部分规定了通信设备，包括船舶和近海用电缆和光缆填充膏的实验方法。本部分规定了填充膏的滴点测定、油分离测定、低温脆性试验、总酸值测定、腐蚀性试验、23℃时介电常数测定、23℃和100℃时的直流电阻率测定等试验方法。
信息：ICS：29.060 CCS：K15 发布：2008-06-26 实施：2009-04-01

ASTM D566-2016 润滑脂滴点的标准试验方法
简介： 5.1x00a0;In general, the dropping point is the temperature at which the grease passes from a semisolid to a liquid state under the conditions of test. This change in state is typical of greases containing as thickeners soaps of conventional types. Greases containing as thickeners materials other than conventional soaps can, without change in state, separate oil. This test method is useful to assist in identifying the grease as to type and for establishing and maintaining bench marks for quality control. The results are considered to have only limited significance with respect to service performance as dropping point is a static test. Note 1:x00a0;Cooperative testing indicates that in general, dropping points by Test Method D5663 and Test Method D2265 are in agreement. In cases where results differ, there is no known significance. However, agreement between producer and consumer as to the test method used is advisable. 1.1x00a0;This test method covers the determination of the dropping point of lubricating grease. 1.2x00a0;This test method is not recommended for use at bath temperatures above 2888201;x00b0;C. For higher temperatures Test Method D2265 should be used. 1.3x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4x00a0;WARNINGx2014;This test method uses mercury-filled thermometers. Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for details and EPAx2019;s websitex2014; http://www.epa.gov/mercury/faq.htmx2014;for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. The responsible subcommittee, D02.G.3, continues to explore alternatives to eventually replace the mercury thermometers. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 6.4 and 8.1.
信息：ICS：75.100 CCS：发布：2016 实施：

KS C IEC 60811-5-1-2006(2016) 电缆和光缆绝缘和护套材料通用试验方法第5－1部分:填充化合物专用方法滴点油分离低温脆性总酸值无腐蚀性组分23℃介电常数23℃和100℃直流电阻率
简介：
信息：ICS： CCS：发布：2006-11-03 实施：

GB/T 3498-2008 润滑脂宽温度范围滴点测定法
简介：警告——本标准可能涉及到有危险的材料、操作和设备。但并未把运用本标准过程的所有安全问题都标出。本标准的使用者在使用之前有责任咨询，并建立相应的安全和保健措施，并确定规章限定的适用范围。本标准适用于测定润滑脂宽温度范围的滴点。
信息：ICS：75.100 CCS：E36 发布：2008-06-23 实施：2008-12-01

ASTM D2265-15 在较宽温度范围内润滑脂滴点的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2015-04-01 实施：

KS C IEC 60811-5-1-2006 电缆绝缘和护套材料的通用试验方法.第5部分:填充复合物的专用方法.第1节:滴点、油分离、较低温脆性、总酸值、无腐蚀性成分.在23℃时的电容率、在23℃和100℃时的直流电阻率
简介：이 규격은 선박 해양용으로 사용되는 케이블, 배전용 및 전기 통신용 전기 케이블과 광 케이
信息：ICS：29.060.20;29.035.20 CCS：K13 发布：2006-11-03 实施：2006-11-03

GB/T 2951.10-1997 电缆绝缘和护套材料通用试验方法第5部分;填充膏专用试验方法第1节:滴点--油分离--低温脆性--总酸值--腐蚀性--23℃时的介电常数--23℃和100℃时的直流电阻率
简介： 本标准规定的试验条件和试验参数适用于通信电缆中的填充膏材料。
信息：ICS：29.060 CCS：K13 发布：1997-10-28 实施：1998-10-01

ASTM D2265-15e1 在较宽温度范围内润滑脂滴点的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2015-04-01 实施：

NF T60-627-2006 石油产品和润滑剂.润滑脂滴点.自动机械方法
简介：
信息：ICS：75.100 CCS：E34 发布：2006-06-01 实施：2006-06-05

GB/T 4929-1985 润滑脂滴点测定法
简介： 本方法适用于测定润滑脂的滴点。
信息：ICS：75.100 CCS：E30 发布：1985-02-06 实施：1985-10-01

ASTM D127-08(2015) 石油蜡包括凡士林滴点熔点的标准试验方法
简介：
信息：ICS：75.140 CCS：发布：2015-01-01 实施：

NF T60-631-2006 石油产品.润滑脂.滴点的测定
简介：
信息：ICS：75.100 CCS：E36 发布：2006-06-01 实施：2006-06-05

GB 4929-1985 润滑脂滴点测定法
简介：
信息：ICS： CCS：E30 发布：1985-02-06 实施：1985-10-01

ASTM D3954-2015 石蜡滴点的标准试验方法
简介： 4.1x00a0;Waxes do not go through a sharp solid-liquid phase change when heated and therefore do not have a true melting point. As the temperature rises, waxes gradually soften or become less viscous. For this reason, the determination of the softening point must be made by an arbitrary but closely defined method if test values are to be reproducible. 4.2x00a0;This test is useful in determining the consistency of waxes, and as one element in establishing the uniformity of shipments or source of supply. 4.3x00a0;This test method has been found suitable for all types of waxes including paraffin, microcrystalline polyethylene, and natural waxes. 1.1x00a0;This test method covers the determination of the ASTM dropping point for waxes. 1.2x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS： CCS：发布：2015 实施：

NF T60-632-2006 石油产品.润滑脂滴点(宽温度范围)的测定
简介：
信息：ICS：75.100 CCS：E36 发布：2006-06-01 实施：2006-06-05

GB/T 3498-1983 润滑脂宽温度范围滴点测定法
简介：本方法适用于测定润滑脂宽温度范围滴点。
信息：ICS：75.100 CCS：E36 发布：1983-03-31 实施：1983-12-01

ASTM D2265-06(2014) 在较宽温度范围内润滑脂滴点的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2014-11-01 实施：

ASTM D2265-06 在较宽温度范围内润滑脂滴点的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2006-05-01 实施：

GB/T 2560-1981 褐煤蜡滴点测定方法
简介： 本方法适用于测定褐煤蜡滴点。方法要点：蜡样装入滴点计的脂杯中，在规定的加热条件下蜡样从脂杯中滴出第一滴蜡液或流出25毫米长蜡液时的温度称为滴点。
信息：ICS：73.040 CCS：D22 发布：1981-04-08 实施：1981-10-01

GOST 32322-2013 润滑脂. 宽温度范围内滴点的测定
简介：
信息：ICS：75.080;75.100 CCS：发布：2013 实施：2015-01-01

ASTM D2265-2006(2014) 超宽温度范围润滑脂滴点的标准试验方法
简介： 5.1x00a0;The dropping point is useful to assist in identifying the grease as to type and for establishing and maintaining bench marks for quality control. The results are to be considered to have only limited significance with respect to service performance because dropping point is a static test. 5.2x00a0;Cooperative testing3 indicates that, in general, dropping points by Test Method D2265 and Test Method D566 are in agreement up to 260x00b0;C. In cases where results differ, there is no known significance. However, agreement between the manufacturer and purchaser as to test method used is advisable. 1.1x00a0;This test method covers the determination of the dropping point of lubricating grease. 1.2x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.100 CCS：发布：2006 实施：

ASTM D3954-15(2022) 蜡滴点的标准试验方法
简介：
信息：ICS：71.100.99 CCS：发布：2022-12-01 实施：

GOST 32394-2013 润滑脂. 滴点试验方法
简介：
信息：ICS：75.100 CCS：发布：2013 实施：2015-01-01

ASTM D2265-2006 超宽温度范围润滑脂滴点的标准试验方法
简介：The dropping point is useful to assist in identifying the grease as to type and for establishing and maintaining bench marks for quality control. The results are to be considered to have only limited significance with respect to service performance because dropping point is a static test. Cooperative testing3 indicates that, in general, dropping points by Test Method D 2265 and Test Method D 566 are in agreement up to 260x00B0;C. In cases where results differ, there is no known significance. However, agreement between the manufacturer and purchaser as to test method used is advisable.1.1 This test method covers the determination of the dropping point of lubricating grease.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E36 发布：2006 实施：

ASTM D2265-22 宽温度范围内润滑脂滴点的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2022-04-01 实施：

GOST ISO 2176-2013 石油制品. 润滑脂. 滴点的测定
简介：
信息：ICS：75.100 CCS：发布：2013 实施：2015-01-01

ASTM D127-05 石油蜡包括凡士林滴点熔点的标准试验方法
简介：
信息：ICS：75.140 CCS：发布：2005-05-01 实施：

KS C IEC 60811-5-1-2021 电缆和光缆的绝缘和护套材料.通用试验方法.第5-1部分:填充化合物专用方法.滴点.油分离.低温脆性.总酸值.无腐蚀成分.23℃下的介电常数.23℃和100℃下的直流电阻率
简介：
信息：ICS： CCS：发布：2021-10-21 实施：

NF C32-011-601-2012 电缆和光缆. 非金属材料的试验方法. 第601部分: 物理试验. 填充化合物的滴点测量
简介：
信息：ICS：29.035.01 CCS：K13;M33 发布：2012-12-01 实施：2012-12-21

SANS 60811-5-1-2004 电缆和光缆的绝缘和护套材料．通用试验方法．第5．1部分：填充化合物的专用方法．滴点．油分离．较低温脆性．总酸度数值．无腐蚀性成分．23℃ 时的电容率和 23℃ 与 100℃ 时的直流电阻率
简介：Specifies the test methods for filling compounds of electric and optical cables used with telecommunication equipment, including cables used in ships and in offshore applications. Gives the methods for drop-point, separation of oil, lower temperature bri
信息：ICS：29.060.20 CCS：K15 发布：2004-09-10 实施：

ASTM D2265-20 在较宽温度范围内润滑脂滴点的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2020-05-01 实施：

DIN EN 60811-601-2012 电缆和光缆. 非金属材料的试验方法. 第601部分:物理试验. 填充化合物的滴点测量 (IEC 60811-601-2012); 德文版本EN 60811-601-2012
简介：
信息：ICS：29.035.01 CCS：K13;M33 发布：2012-12 实施：2012-12-01

ASTM D127-87(2004) 石油蜡包括凡士林滴点熔点的标准试验方法
简介：
信息：ICS：75.140 CCS：发布：2004-07-01 实施：

ASTM D566-20 润滑脂滴点的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2020-05-01 实施：

BS EN 60811-601-2012 电缆和光缆. 非金属材料试验方法. 物理试验. 填充化合物的滴点测量
简介：
信息：ICS：29.035.01 CCS：M33;K15 发布：2012-07-31 实施：2012-07-31

NF C32-033/A1-2004 电缆和光缆的绝缘和护套材料.通用试验方法.第5-1部分:填充复合物的专用方法.滴点.油的分离.较低温脆性.总酸值.无腐蚀性成分.23℃时的介电常数.23℃和100℃的直流电阻率
简介：
信息：ICS：29.035.20 CCS：K13 发布：2004-07-01 实施：2004-07-05

ISO 2176-1995/Amd 1-2020 石油产品.润滑脂.滴点的测定.修改件1
简介：
信息：ICS：75.100 CCS：发布：2020-03-11 实施：

IEC 60811-601:2012 电光纤电缆 - 非金属材料的测试方法 - 第601部分:物理测试 - 填充化合物滴点的测量
简介：
信息：ICS：29.060.20 CCS：发布：2012-03-13 实施：

IEC 60811-5-1 Edition 1.1-2004 电缆和光缆用绝缘和护套材料.通用试验方法.第5-1部分:填充复合物的专用方法.滴点.油分离.较低温脆性.总酸值.无腐蚀性成分.23鳦时的电容率.23鳦和100鳦时的直流电阻率
简介：Specifies the test methods for filling compounds of electric cables used with telecommunication equipment. Gives the methods for drop-point, separation of oil, lower temperature brittleness, total acid number, absence of corrosive components, permittivit
信息：ICS：29.035.01 CCS：K13 发布：2004-01 实施：

ASTM D2265-19 在较宽温度范围内润滑脂滴点的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2019-06-01 实施：

IEC 60811-601-2012 电缆和光缆.非金属材料试验方法.第601部分:物理试验.填充化合物的滴点测量
简介：
信息：ICS：29.035.01;29.060.20 CCS：K15 发布：2012-03-01 实施：

ASTM D7077-2004 通过溶液和悬浮物的重量评价滴点尺寸的标准试验方法
简介：1.1 This standard test method uses a simulated in-use study to measure the drop size by weight and to determine the number of drops per container for solutions and suspensions contained in a package system designed to deliver product drop-wise through a controlled size orifice by squeezing or compressing the package.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
信息：ICS：17.100 CCS：N13 发布：2004 实施：

ISO 22286:2018 石油产品和润滑剂.用自动装置测定润滑脂滴点
简介：
信息：ICS：75.100 CCS：发布：2018-10-25 实施：

GOST IEC 60811-5-1-2011 电缆填充复合物的专门试验方法.滴点.油分离.较低温脆性.总酸值.无腐蚀性成分.23℃时的电容率.23℃和100℃时的直流电阻率
简介：
信息：ICS：29.035.01 CCS：发布：2011 实施：2013-01-01

KS M ISO 2176-2003 石油产品.润滑脂.滴点的测定
简介：이 규격은 그리스의 적점을 측정하는 방법에 대하여 규정한다.비 고 1. 적점 시험
信息：ICS：75.100 CCS：E36 发布：2003-12-06 实施：2003-12-06

ASTM D566-17 润滑脂滴点的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2017-05-01 实施：

ASTM D566-02(2009) 润滑脂滴点的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2009-04-15 实施：

IEC 60811-5-1 AMD 1-2003 电缆和光缆用绝缘和护套材料.通用试验方法.第5-1部分:填充复合物的专用方法.滴点.油分离.较低温脆性.总酸值.无腐蚀性成分.23℃时的介电常数.23℃和100℃时的直流电阻率.修改件1
简介：This standard is Insulating and sheathing materials of electric and optical cables - Common test methods - Part 5-1: Methods specific to filling compounds - Drop point - Separation of oil - Lower temperature brittleness - Total acid number - Absence of corrosive components - Permittivity at 23 °C - DC resistivity at 23 °C and 100 °C; Amendment 1.
信息：ICS：29.035.01 CCS：K13 发布：2003-12 实施：

ASTM D566-2017 润滑脂滴点的标准试验方法
简介： 5.1x00a0;In general, the dropping point is the temperature at which the grease passes from a semisolid to a liquid state under the conditions of test. This change in state is typical of greases containing as thickeners soaps of conventional types. Greases containing as thickeners materials other than conventional soaps can, without change in state, separate oil. This test method is useful to assist in identifying the grease as to type and for establishing and maintaining bench marks for quality control. The results are considered to have only limited significance with respect to service performance as dropping point is a static test. Note 1:x00a0;Cooperative testing indicates that in general, dropping points by Test Method D5663 and Test Method D2265 are in agreement. In cases where results differ, there is no known significance. However, agreement between producer and consumer as to the test method used is advisable. 1.1x00a0;This test method covers the determination of the dropping point of lubricating grease. 1.2x00a0;This test method is not recommended for use at bath temperatures above 2888201;x00b0;C. For higher temperatures Test Method D2265 should be used. 1.3x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4x00a0;WARNINGx2014;This test method uses mercury-filled thermometers. Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for details and EPAx2019;s websitex2014; http://www.epa.gov/mercury/faq.htmx2014;for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. The responsible subcommittee, D02.G.3, continues to explore alternatives to eventually replace the mercury thermometers. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 6.4 and 8.1. 1.6x00a0;This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical ......
信息：ICS：75.100 CCS：E36 发布：2017 实施：

ASTM D127-08 石油蜡包括凡士林滴点熔点的标准试验方法
简介：
信息：ICS：75.140 CCS：发布：2008-05-01 实施：

KS M ISO 6299-2003 石油产品.润滑脂滴点的测定(大温度范围)
简介：이 규격은 넓은 온도 범위에 대한 윤활 그리스의 적점을 측정하는 시험 방법에 대하여 규
信息：ICS：75.100 CCS：E30 发布：2003-11-10 实施：2003-11-10

KS C IEC 60811-601-2016(2021) 电缆和光缆非金属材料试验方法第601部分:物理试验填充化合物滴点的测量
简介：
信息：ICS： CCS：发布：2016-12-28 实施：

TCVN 2697-1978 润滑脂.滴点用试验方法
简介：
信息：ICS： CCS：发布：2008 实施：

ASTM D566-97 润滑脂滴点的标准试验方法
简介：
信息：ICS： CCS：发布：2002-04-10 实施：

KS C IEC 60811-601-2016 电气和光纤电缆 - 试验方法非金属材料 - 601部分:物理测试 - 填充化合物的滴点的测定
简介：
信息：ICS： CCS：发布：2016-12-28 实施：

SH/T 0800-2007 蜡滴点测定法
简介： 1.1 本标准规定了测定蜡滴点的试验方法，适用于包括石蜡、微晶蜡、聚乙烯蜡、调合蜡和天然蜡在内所有类型的非液态蜡。 1.2 本标准可能涉及某些有危险的材料、设备和操作，但并无意对此有关的所有安全问题都提出建议。因此，在使用本标准之前，用户有责任建立适当的安全和防护措施，并制定有适用性的管理制度。
信息：ICS：75.140 CCS：E42 发布：2007-08-01 实施：2008-01-01

ASTM D566-97e1 润滑脂滴点的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2002-04-10 实施：

ASTM D566-16 润滑脂滴点的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2016-04-01 实施：